12
GB
O R I G I N A L I N S T R U C T I O N S
CHARACTERISTICS OF TOOL
Reciprocating saw is a tool for the cutting the wood surfaces and surfaces which are made of wood-based materials, plates of
polyethylene or polypropylene, or metal by using the appropriately selected blades to the type of material. Due to easy exchange
of blades, which does not require any additional tools,, the saw allows for an extensive use in construction works. Correct, reliable,
and safe operation of the device is dependent on its proper use, therefore:
Prior to working with the tool, you should read all the instruction and keep it around.
For any injury and damage, which are resulting from failure to comply with its designation, lack of compliance with the safety
regulations and instructions of this manual, the supplier is not responsible. The tool misuse causes also the loss of user’s rights
to the guarantee, as it would be a non-compliance with the contract.
EQUIPMENT
The product is supplied in a complete state and requires no assembly. The product is supplied with the battery charger and
charging station (charger).
TECHNICAL PARAMETERS
Parameter
Units
Value
Catalogue No.
YT-82904
Rated voltage
[V]
12
Rated speed
[min
-1
]
0 - 3000
Cutting thickness (max)
- wood
[mm]
65
- plastic
[mm]
50
- metals
[mm]
8
Blade holder
universal 1/2” (12.7 mm)
Blade stroke
[mm]
12.7
Noise level
- sound pressure
[dB(A)]
83.58 ± 3.0
- power
[dB(A)]
94.58 ± 3.0
Vibration level - cutting an MFD board (main / additional handle)
[m/s
2
]
12.86 ± 1.5 / 10.13 ± 1.5
Vibration level - cutting of metal sheet (main / additional handle)
13.78 ± 1.5 / 11.92 ± 1.5
Ingress protection rating
IPX0
Protection class
III
Weight
[kg]
1.0
Battery type
Li-ion
Battery capacity
[Ah]
1.5
Charger
Input voltage
[V]
100 - 240
Power frequency
[Hz]
50 / 60
Output voltage
[V]
12
Output current
[A]
2
Rated power
[W]
35
Charging time
[h]
1
GENERAL SAFETY CONDITIONS
NOTE!
Get acquainted with all the instructions below. Failure to observe them may lead to an electric shock, fi re or injuries. The
notion of electric tool used in the instructions applies to all the tools which are powered with electric current, both wire tools and
wireless ones.
OBSERVE THE FOLLOWING INSTRUCTIONS
Place of work
The place of work must be properly illuminated and clean.
Disorder and poor illumination may be a cause of accidents.
Do not work with electric tools in explosive environments, or those which contain infl ammable liquids, gases or vapours.
Electric tools generate sparks, which may cause a fi re in case of contact with infl ammable gases or vapours.
Do not allow children and outsiders to the place of work.
A lack of concentration may result in a loss of control over the tool.
Summary of Contents for YT-82904
