background image

2

Congratulations on the purchase of your YAZOO/KEES mower. This manual has been prepared
for the owners and operators of the models called out on the front cover of this manual. Read,
understand and follow the safety and operating instructions.

Continuous dedication to improve our products require that specifications and design are sub-
ject to change without notice.

! WARNING

Failure to follow cautious operating practices can result in serious injury to the operator or other per-
sons.  The owner must understand these instructions, and must allow only trained persons who un-
derstand these instructions to operate the mower.  Each person operating the mower must be of
sound mind and body and must not be under the influence of any mind altering substance.

! CAUTION

1. Keep all shields, guards and safety devices in place and in proper working condition.
2. Stop engine and remove spark plug wires or remove key before adjusting, servicing, or performing
maintenance.

TECHNICAL ASSISTANCE

If you have any questions pertaining to your mower contact your dealer.  To locate the nearest dealer
please call: 1-877-368-8873 or for more information go our web site at www.yazookees.com

For technical assistance please write:  Yazoo/Kees, 700 Park Street, Beatrice, Ne 68310
or call:1-877-368-8873

WARNING: Engine exhaust, some of it’s constituents, and certain vehicle componets con-

tain or emit chemicals known to the State of California to cause cancer and birth defects or

other reproductive harm.

WARNING: Battery posts, terminals and related accessories contain lead and lead com-

pounds, chemicals known to the State of California to cause cancer and

birth defects or other reproductive harm. Wash hands after handling.

Summary of Contents for ZVKE61260

























Reviews: