Yealink CP969 Administrator'S Manual Download

Page: 789 / 868

Appendix

767

Appendix

Appendix A: Glossary

802.1x

--an IEEE Standard for port-based Network Access Control (PNAC). It is a part of the IEEE

802.1 group of networking protocols. It provides an authentication mechanism to devices
wishing to attach to a LAN or WLAN.

ACS

(Auto Configuration server)

responsible for auto-configuration of the Central Processing

Element (CPE).

Cryptographic Key

--a piece of variable data that is fed as input into a cryptographic algorithm

to perform operations such as encryption and decryption, or signing and verification.

DHCP

(Dynamic Host Configuration Protocol)

built on a client-server model, where designated

DHCP server hosts allocate network addresses and deliver configuration parameters to
dynamically configured hosts.

DHCP Option--

can be configured for specific values and enabled for assignment and

distribution to DHCP clients based on server, scope, class or client-specific levels.

DNS

(Domain Name System)

a hierarchical distributed naming system for computers, services,

or any resource connected to the Internet or a private network.

EAP-MD5

(Extensible Authentication Protocol-

Message Digest Algorithm 5

)

only provides

authentication of the EAP peer to the EAP server but not mutual authentication.

EAP-TLS

(Extensible Authentication Protocol-Transport Layer Security)

–

provides for mutual

authentication, integrity-protected cipher suite negotiation between two endpoints.

PEAP-MSCHAPv2

(Protected Extensible Authentication Protocol-Microsoft Challenge

Handshake Authentication Protocol version 2)

–

provides for mutual authentication, but does not

require a client certificate on the IP phone.

FAC

(Feature Access Code)

special patterns of characters that are dialed from a phone keypad

to invoke particular features.

HTTP

(Hypertext Transfer Protocol)

used to request and transmit data on the World Wide

Web.

HTTPS

(Hypertext Transfer Protocol over Secure Socket Layer)

a widely-used communications

protocol for secure communication over a network.

IEEE

(Institute of Electrical and Electronics Engineers)

a non-profit professional association

headquartered in New York City that is dedicated to advancing technological innovation and
excellence.

LAN

(Local Area Network)

used to interconnects network devices in a limited area such as a

Summary of Contents for CP969





































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for CP969

Reviews:

Related manuals for CP969

Brands by name

Popular brands

Yealink CP969, Administrator'S Manual

Search results

Summary of Contents for CP969

Reviews:

Related manuals for CP969

Brands by name

Popular brands