Yealink CP969 Administrator'S Manual Download | Manualshive

Page: 461 / 868

background image

Configuring Advanced Features

439

Parameter

Permitted Values

Default

Description:

Enables or disables the IP phone to answer an incoming call by picking up the handset,
pressing the Speakerphone key or pressing the HEADSET key directly.

0

-Disabled

1

-Enabled

If it is set to 0 (Disabled), you need to tap the corresponding line key or the

Answer

soft key

to answer an incoming call after picking up the handset, pressing the Speakerphone key or
pressing the HEADSET key.

Note

: It is not applicable to CP960 IP phones.

Web User Interface:

None

Phone User Interface:

None

Call Recording Using Soft Key

Yealink IP phones support recording calls (audio-only calls or video calls) or conferences during
a call. By default, the recorded files are saved in the internal SD card. You can also save the
recorded files in the connected USB flash drive. For SIP-T58V/T58A/T56A IP phones, if you
connect the USB flash drive to the IP phone, the recorded files will be saved according to the
priority: USB flash drive >Internal SD card. For CP960 IP phones, if you connect the USB flash
drive to the IP phone, you can choose to save the recorded files to the Internal SD card or USB
flash drive.

In addition, the IP phones allow users to record audio and access audio recording files by

Recorder

application. For more information, refer to

Yealink phone-specific user guide

You can also record audio-only calls by tapping record/URL record key. For more information,
refer to

Record and URL Record

on page

Note

Procedure

Call recording feature can be only configured using the configuration files.

Central Provisioning

(Configuration File)

<y0000000000xx>.cfg

Configure the recording feature.

Parameter:

Before recording any call, especially those involving PSTN, it is necessary to know about the rules
and restrictions of any governing call-recording in the place you are in. It is also very important to
have the consent of the person you are calling before recording the conversation.

«
...
459
460
461
462
463
...
»

Summary of Contents for CP969





































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for CP969

Brand: Homtom Pages: 15

Brand: jablotron Pages: 7

Brand: Audiovox Pages: 39

Brand: Snom Pages: 2

Brand: Ulefone Pages: 47

Brand: snopfon Pages: 46

Brand: BCM Pages: 26

Brand: DDM Pages: 24

Brand: Xiaomi Pages: 8

8900 - Curve - GSM

Brand: Blackberry Pages: 48

Brand: Huawei Pages: 88

Brand: Huawei Pages: 94

Brand: Huawei Pages: 53

Brand: Huawei Pages: 12

Brand: Huawei Pages: 16

Brand: Huawei Pages: 20

Brand: Huawei Pages: 12

Brand: Huawei Pages: 20

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands