Yealink SIP-T4X Administration Manual Download

Page: 184 / 466

Configuring Advanced Features

169

TLV Type

TLV Name

Description

The advertised capabilities of PMD.

Auto-Negotiation is: 100BASE-TX (full
duplex mode), 100BASE-TX (half duplex
mode), 10BASE-T (full duplex mode),
10BASE-T (half duplex mode).

TIA

Organizationally

Specific TLVs

Media Capabilities

The MED device type of the IP phone and
the supported LLDP-MED TLV type can be
encapsulated in LLDPDU.

The supported LLDP-MED TLV types are:
LLDP-MED Capabilities, Network Policy,
Extended Power via MDI-PD, Inventory.

Network Policy

Port VLAN ID, application type, L2 priority
and DSCP value.

Extended
Power-via-MDI

Power type, source, priority and value.

Inventory –
Hardware Revision

Hardware revision of phone.

Inventory –
Firmware Revision

Firmware revision of phone.

Inventory –
Software Revision

Software revision of phone.

Inventory – Serial
Number

Serial number of phone.

Inventory –
Manufacturer Name

Manufacturer name of phone.

The default value is “yealink”.

Inventory – Model
Name

Model name of phone.

Asset ID

Assertion identifier of phone.

The default value is “asset”.

Procedure

LLDP can be configured using the configuration files or locally.

Configuration File

<y0000000000xx>.cfg

Configure LLDP feature.

For more information, refer to

LLDP

on page

344

Local

Web User Interface

Configure LLDP feature.

Summary of Contents for SIP-T4X



















































































































































































































































































































































































































































































Search results

Summary of Contents for SIP-T4X

Reviews:

Related manuals for SIP-T4X

Brands by name

Popular brands

Yealink SIP-T4X, Administration Manual

Search results

Summary of Contents for SIP-T4X

Reviews:

Related manuals for SIP-T4X

Brands by name

Popular brands