Call Features
161
multicast.listen_address.1.label = Paging1
Permitted
Values
String within 99 characters
Default
Blank
Web UI
Directory->Multicast IP->Multicast Listening->Label
Parameter
multicast.listen_address.X.channel
[1]
<y0000000000xx>.cfg
Description
It configures the channel that the IP phone listens to.
Example
:
multicast.listen_address.1.channel = 2
Permitted
Values
0
-the IP phone can receive an RTP stream of the pre-configured multicast address from the IP phones run-
ning firmware version 80 or earlier, from the IP phones listen to the channel 0, or from the available third-
party devices (for example, Cisco IP phones).
1 to 25
-the IP phone can receive an RTP stream of the pre-configured multicast address on the channel 1
to 25 respectively from Yealink or Polycom IP phones.
26 to 30
-the IP phone can receive the RTP stream of the pre-configured multicast address on the channel
26 to 30 respectively from Yealink IP phones.
Default
0
Web UI
Directory->Multicast IP->Multicast Listening->Channel
[1]
X ranges from 1 to 31
Multicast Paging Settings
You can configure some general settings for multicast paging, for example, specify a codec, configure the volume and
audio device for listening to a paging call.
By default, all the listening groups are considered with a certain priority from 1 (lower priority) to 31 (higher priority). If
you neither want to receive some paging calls nor miss urgent paging calls when there is a voice call or paging call, or
when DND is activated, you can use the priority to define how your phone handles different incoming paging calls.
Paging Barge
You can set your phone whether an incoming paging call interrupts an active call.
The Paging Barge defines the lowest priority of the paging group from which the phone can receive a paging call when
there is a voice call (a normal phone call rather than a multicast paging call) in progress. You can specify a priority that
the incoming paging calls with higher or equal priority are automatically answered, and the lower ones are ignored.
If it is disabled, all incoming paging calls will be automatically ignored.
Paging Priority
You can set your phone whether a new incoming paging call interrupts a current paging call.
The Paging Priority feature decides how the phone handles incoming paging calls when there is already a paging call
on the phone. If enabled, the phone will ignore incoming paging calls with lower priorities, otherwise, the phone will
answer incoming paging calls automatically and place the previous paging call on hold. If disabled, the phone will
automatically ignore all incoming paging calls.
Summary of Contents for W60P Telesystem
