background image

 

 

TA1600/2400/3200  User  Manual 

 

77/87 

 

Figure 11-7 Server Address 

 

 

AES Key

 

If the configuration file is encrypted by AES key, you need to fill the key in this 
field. 

 

Always Apply 

With No, it will compare the current configuration file with the last updated one, if 
the contents are the same no update will be applied. With Yes, it will always apply 
the updated configuration file.

 

Firmware Upgrade 

TA1600/2400/3200 can be upgraded to a new firmware version via network or locally. 
Users  could  upgrade  firmware  via  HTTP  or TFTP. Please  go  to 

System→  System 

Preferences→ Firmware Update

 to do upgrade. 

 

Notes: 

1. 

If “Reset configuration to Factory Defaults” is enabled, the system will be restored 
to factory default settings. 

2. 

When updating the firmware, please don’t turn off the power. Or the system will 
be damaged. 

3. 

If  you  are  trying  to  upgrade  through  HTTP,  please  make  sure  that  your 
TA1600/2400/3200 is able to  visit external network, or it cannot access Yeastar 

Summary of Contents for 16-FXS
























































































Reviews: