36
37
Do not pull the knurled screws too tight. They may break and the joints may squeak.
Instead readjust the screw inside the bottom as in Step 1.
If necessary, use Teflon spray in case of joint squeak.
Page 8
Make sure the bolt at the bottom of your m!ka Studio Light has its black plastic sleeve
on. The sleeve is needed to fit smoothly to the various mounting devices.
Make sure that the mounting device has a yellow spacer installed.
- No Yellow Spacer will be needed when using the metal bushing.
Page 9
Your m!ka Studo Light is prebalanced. Do not pull the knurled screws too tight. They
may break and the joints may squeak.
In case, use Teflon spray in case of joint squeak.
Page 10
Pay attention when connecting your m!ka Studio Light to mains voltage!
Step 1: Always connect the low voltage connector prior to connecting to the mains.
Step 2: Select the correct mains adapter for your country and clip it to the wall PSU.
Page 11
Your m!ka Studio Light has an integrated DIM function.
- Press short for switching ON/OFF.
Press long to DIM up, press long again to DIM down. m!ka Studio Light will remember
the last DIM value when switching it on again.
Page 12
To secure proper upright mounting of the MMS pole we suggest drilling a minimum
hole of 12mm diameter for the PDM Kit.
If you need to use your own threaded bolt make sure you use M10 metric thread.
The cable organizer clip will help to tidy your wiring.
Page 13
- Never use the Power Sting other than with the original m!ka Bushing. Table clamps
are not suitable to hold an MMS arm. Use a gripper to fix the Power Sting.
Page 14
When installing the m!ka Ceiling Mount it is your obligation to verify that your ceiling
and your fasteners are suitable to hold the load.
Page 15
When installing the m!ka Wall Mount it is your obligation to verify that your wall and
your fasteners are suitable to hold the load.
Page 16
Make sure you have checked the max. payload of your m!ka Monitor Arm. The infor
mation is printed on the product label on the rearside of the QuickFix.
See Page 21 for how to secure a minimum headroom under your monitor.
Page 17
In order to prevent unintended changes to the MMS height position simply remove
the thumbscrews by pulling them out. Before you remove the screws make sure they
are all properly tightend.
Page 18
The MMS QuickFix adapter is suitable to be used with VESA 75 and VESA 100 fixtures.
m!ka
Remarks
Summary of Contents for m!ka Wall Mount
