background image

3

7. The tire pressure should be checked prior to each use.  The recommended inflation pressure is the

maximum tire pressure which is printed on the tire’s sidewall.  

Improper tire pressure may cause

instability and may prevent proper braking or steering

.

8. Modification of this vehicle or removal of any original equipment or safety decals may render the

vehicle unsafe or illegal.  

Never remove any chained guard, or belt clutch guard

.  These covers

are for the riders’ protection.

9. The vehicle should never be started without first checking to see that the throttle is in 

idle

 position. Do

not start engine without verifying proper function of the throttle.

10.

Never attempt to start this vehicle without having the operator sitting in the proper position

to ensure control of the kart.

11. The operator’s ability to operate this off-road vehicle safely is largely dependent upon the operator’s

ability to exercise proper judgement.  An operator also must not be too small or too large for controlled

operation. The operator must be at least 16 years of age and have understanding, mental capacity and

physical capability to safely operate this vehicle.  This vehicle should only be operated after mature,

supervised instruction and sufficient practice in non-congested areas.

12.

This  vehicle  is  designed  for  one  operator  only.   

An  operator  on  any  vehicle  must  be  of

sufficient age, understanding, mental capacity, and physical capability to act to protect himself/herself,

and wear a D.O.T approved helmet at all times.  

This kart is not recommended for weights

exceeding 200 pounds.

13. The engine should be stopped when the vehicle is not in use.

14.

Loose  clothing,  long  hair,  or  articles  worn  by  any  riders  must  be  fully  contained,  or

covered to prevent them from possibly being caught in rotating parts of the vehicle or the

surrounding environment while riding.  Failure to obey could endanger the personal safety

of the Rider

.

15.

Do not place hands, feet, or any other part of the body or any clothing near the engine,

muffler, wheels, chain, and other rotating parts of the vehicle while riding or running the

engine

. Caution must be used in performing required maintenance on or near an operating engine.

Special caution should be taken after the engine has been running, since the engine and other drive

components may be extremely hot.

16. Wet, slippery, rough, or steep terrain is potentially dangerous and may result in injury if proper caution

is not observed. Slow speeds are required to safely operate this vehicle under those conditions. The

Operator must use mature judgement, skill, and experience to choose a speed suitable for the terrain

and riding conditions.

17.

The Governor settings for this vehicle’s engine must not be tampered with, altered or

changed

. The governor is set by the engine manufacturer and limits the maximum speed of the

engine (and vehicle) and protects the 

engine

 from damage.  Excessive speeds are potentially

dangerous to the rider and the engine. 

The top speed for this vehicle is 34 mph.

Summary of Contents for 32001 Series




















Reviews: