background image

5

6

0

.

01

%  ±

2mV 

1mav

1A

300PPM

/

0~2A

0~2A

0~2A

0~2A

2A

0.6~2A

0.6~2A

0.6~2A

Ripple noise

Temperature Coefficient 

Output Current

Overload current

≤ 

0.5mvrms (5Hz-1MHz) Iomax greater than 1A

Load Rated degrees

1502USB

1502DD

1502D+

0

.

1V

0

.

1V

0

.

1V

0

.

1V

10mA

10mA

10mA

10mA

DC

 

0V

~

15V

/

0V

~

5V

DC

 

0V

~

15V

/

0V

~

5V

DC

 

0V~15V

DC

 

0V~15V

Modle

Function

Voltage display precision

Current display precision

Outpunt voltage choice

Mobile singal shows

PSP power supply function

Yes

Yes

No

No

Yes

No

No

No

III. Performance Comparison Table

IV. Instruction manual

Front panel introduce

A

+

USB-DC 5V

OUT PUT

RF

POWER

15V

5V

1502USB

V

VOLTAGE

0

15

PS-1502DD

DC POWER SUPPLY

CURRENT

VOLTAGE

POWER

PS-1502D

DC POWER SUPPLY

POWER

+

5V

15V

CURRENT

VOLTAGE

VOLTAGE

1

1

2

2

3

4

4

4

14

9

10

12

12

5

5

6

6

7 8

8

13

PS-1502DD

DC POWER SUPPLY

CURRENT

VOLTAGE

POWER

+

PHS/CDMA

11

13

1.Current indicator
2.Voltage indicator
3.Output current adjust
4.Voltage gears adjust
5.Power switch
6.Output negative
7.Grounding terminal

8.Output positive
9.Voltage fine tuning knob
10.Voltage coarse tuning knob
11.PHS/CDMA switch knob
12.USB interface
13.Mobile phone RF signal indicator
14.Voltage adjust knob 

Use in

For  maintenance  of  NOKIA/  MOTOROLA/  LG/  Lenovo  /  Sony  Ericsson/  Other 
brand  mobile  phones,  and  BP  machine.  According  to  mobile  voltage  setting  the 
voltage and setting the overload protect current. Don’t adjust to high to prevent too 
much current and burn the phone.

V. Warning

1.    Must set the output voltage and current  properly  before  connect  the  mobile 
       phone, do not adjust the voltage, current and convert the output  pressure,  so 
       as not to burn the mobile phone.
2.    Power supply are not allow at full load state for long time. Control your utilizat-
       ion rate of less than 60%, ro they may cause human early failure.  When  place 
       order, you should be based on the actual operating current includes an  allow-
       ance.

Dedicated output connections

VI. PSP power supply function

1502USB power supply function with mobile phone PSP power supply function, a 
square USB port on the back panel, and front panel with a flat-shaped USB port of 

Summary of Contents for 1502USB






Reviews: