LEFT_ANGLE (
Column 16
):
It must be maximum 3 characters and in integer format.
(The cutting angle of
the left side of the profile. For example, 450 value should be written here for 45 degrees. 865 should be
written for an angle of 86.5 degrees.)
RIGHT_ANGLE (
Column 17
):
It must be maximum 3 characters and in integer format.
(The cutting angle of
the right side of the profile. For example, 450 value should be written here for 45 degrees. 865 should
be written for an angle of 86.5 degrees.)
SIDE (
Column 18
):
It must be maximum 1characters and in integer format.
(The value written here refers to
the direction of the frame. Introducing the direction of the profile to the list should be in the following
format).
1 = Left
2 = Upper
3 = Right
4 = Bottom
CUTED (
Column 19
):
It must be maximum 1characters and in integer format.
(B value must be 0 as default.
After the profile is cut, the value there is automatically changed to 1. 0 means that the profile is not
cut, and 1 means that the profile is cut.)
HEIGHT (
Column 20
):
It must be maximum 8 characters and in integer format
. (The height of the profile
must be entered in this field.)
SELLER (
Column 21
)
:
It must be maximum 24 characters and in text format.
(If there is a second customer,
it is written in this field. As an example, the customer of the customer can be evaluated in this
context.)
IMMAGE (
Column 22
):
It must be maximum 50 characters and in text format.
(The path to the folder where
the image is located should be written in this column. This path should be entered as \\ X \\ IMAGE \\
........... Also, images must be in .bmp format and monochrome.)
PAIR (
Column 23
):
It must be maximum 4 characters and in integer format
.
The program number of the
profile that corresponds to the profile that is cut is written in this column. For example, assume that
the program number of the left profile no1 in a frame of Pose1 is 3 and the program number of the
right profile no 3 that corresponds to this profile is 7. In this case, 7 should be written in PAIR section
on the line of program no 3. In the same way, 3 should be written in PAIR section on the line of
program no 7. This means that the profile corresponding to the profile registered in program no 3 is
registered in program no 7.)
TOTAL SIZE (
Column 24
):
It must be maximum 8 characters and in text format.
(Full length of the profile
placed to be cut should be entered here by multiplying by 10. For example, 60000 should be entered
here for a profile with 6 meters (6000 mm) length).
PICE_NO (
Column 25
):
It must be maximum 8 characters and in integer format
.
(
The part number must be
written in this column to indicate the number of parts cut from the full length profile placed. As an
example, if we are to cut 4 parts from the profile, then, the number of the first part will be 1, the number
of the second part will be 2, and so on.)
WIDTH (
Column 26
):
It must be maximum 8 characters and in integer format
. (The width from the
compression point of the profile placed should be written in this column. The value should be entered
by multiplying by 10. For example, if the profile width is 56 mm, 560 should be written here.)
9. CUTTING LIST INFORMATION
139
Summary of Contents for PCC 6505
