2-4
<Toc>
<2. Initial Settings>
IM 05E01D02-41E
3.
Press the
SET/ENT
key once to register the
required setpoint.
PVE1
TME
PVE2
PRG1
HLD
PRG2
SET/ENT
1
PRG
2
PRG
RESET
P V
S P
4.
Press the
SET/ENT
key once to display the
parameter “UNIT” (PV input unit).
PVE1
TME
PVE2
PRG1
HLD
PRG2
SET/ENT
1
PRG
2
PRG
RESET
P V
S P
Displays
parameter
“UNIT”.
5.
Press the
SET/ENT
key once to display the
parameter “RH” (maximum value of PV
input range).
PVE1
TME
PVE2
PRG1
HLD
PRG2
SET/ENT
1
PRG
2
PRG
RESET
P V
S P
Displays
parameter
“RH”.
6.
Press the
or
key to display the
required setpoint. The figure below shows
an example of setting the maximum value
of PV input range to 200.0
⬚
C.
PVE1
TME
PVE2
PRG1
HLD
PRG2
SET/ENT
1
PRG
2
PRG
RESET
P V
S P
Blinks during
change.
7.
Press the
SET/ENT
key once to register the
setpoint.
PVE1
TME
PVE2
PRG1
HLD
PRG2
SET/ENT
1
PRG
2
PRG
RESET
P V
S P
8.
Press the
SET/ENT
key once to display the
parameter “RL” (minimum value of PV
input range).
PVE1
TME
PVE2
PRG1
HLD
PRG2
SET/ENT
1
PRG
2
PRG
RESET
P V
S P
Displays
parameter
“RL”.
9.
Press the
or
key to display the
required setpoint. The figure below shows
an example of setting the minimum value
of PV input range to 0.0
⬚
C.
PVE1
TME
PVE2
PRG1
HLD
PRG2
SET/ENT
1
PRG
2
PRG
RESET
P V
S P
Blinks during
change.
10.
Press the
SET/ENT
key once to register the setpoint.
PVE1
TME
PVE2
PRG1
HLD
PRG2
SET/ENT
1
PRG
2
PRG
RESET
P V
S P
If the type of input is voltage, also config-
ure the PV Input Decimal Point
Position(SDP), Maximum Value of PV Input
Scale(SH) and Minimum Value of PV Input
Scale(SL) parameters that follow this step.
11.
To set the type of control output, see steps
7 and later in “2.4 Setting Control Output
Type.” To finish settings, press the
SET/ENT
key
for more than 3 seconds. This returns you
to the display shown at power-on (figure
below).
Stop (RESET) state
PVE1
TME
PVE2
PRG1
HLD
PRG2
SET/ENT
1
PRG
2
PRG
RESET
P V
S P
Displays PV.
The PV display in the figure above shows
the error code for input burnout (
) if
PV input wiring is not yet complete. The
error code disappears when you wire the
PV input terminals correctly.
1st Edition : May 31,2000-00
Summary of Contents for UP350
