background image

​RES = total judgement

​Tightening judgement OK or NOK

A: tightening OK

N: tightening NOK

​VAL = Output Value

​Output value at shut-off

​PLS = number of impulses

​Number of impulses from Start value to value tool shut-off

​INF = tightening result details

Aok = OK

Udr: under, tool shut-off below cut value

Ovr: shut-off at value higher than max value

N55: shut-off at too low number impulses

N57: shut-off at too many impulses

Slw: number of impulses exceeded the slow error impulses(70) including the

        number of impulses below start value

Impulse data history

The tool has a memory of the last 5 tightenings with the value of each impulse.

Select PULSE DATA with the Up and Down arrow keys and press ENT to enter this function. ​

​Result: 20 = the average on which the tool has shut-off.

NUM: 6 = number of impulses, including the impulses lower than start value.​

6-  12-  15-  19-  20-  21 = the value of each impulse.

If you have a high number of impulses it will not fit on one screen, press NEXT to move to the next or press PREV for previous screen.

Test Mode.​

In the test mode the tool can be operated without shut-off. After releasing the trigger, the screen will show the value of each impulse. This function can be used for parameter setting, output
adjustment and tightening analyze (hard or soft joint).

​When using this function take care of the CC-1 cable connected to the tool, so it won't entangle with rotating parts or cause dangerous circumstances.

To use this function: Connect the PC-1 to the tool with the CC-1 cable.

Select TEST MODE with the up and down arrow keys and press ENT to enter this function.

Summary of Contents for YZ-T600E















Reviews: