Yokota YZ-T800E Manual Download

Page: 6 / 14

Pulse interval: longer

Tool output : lower

Pulse interval : shorter

Never adjust fully at max or min, always at least 60 degrees from min and max.

Using the Programming Console PC-1

Connect the PC-1 with cable CC-1 to the tool.

Programming Console PC-1

1 Mounting hole

2 Display screen

Displays tightening result, setting item and set value

3 Function key

Switching of tightening screen, setting screen and or of display screen

4 Numeric key

Enter the set value

5 CAN key

Return to the previous screen

6 ENT key

Determine items and input value

7 Up, down, left and right key

Move the selection of setting items up and down

8 PRC05 connector

Cable connector

Start Screen

After connecting the PC-1 with cable CC-1 to the YZ-T tool it will take approx. 5 seconds for the PC-1 to start up, please see below following screens:

Summary of Contents for YZ-T800E















Search results

Summary of Contents for YZ-T800E

Reviews:

Related manuals for YZ-T800E

Brands by name

Popular brands

Yokota YZ-T800E, Manual

Search results

Summary of Contents for YZ-T800E

Reviews:

Related manuals for YZ-T800E

Brands by name

Popular brands