background image

17

8. Quality Assurance and Warranty

8.1 Warranty info

Yolin will offer a limited warranty for any failure caused by the product defects under normal use during the

warranty period.

The product is warranted for 12 months from the date out of factory.

8.2 Warranty does not cover

The shell is opened.

The connector is damaged.

Scratches on the appearance after the product is out of factory.

Scratched or broken wires

Failure or damage caused by force majeure (e.g. fire, earthquake, etc.) or natural disaster (e.g. lightning strike, etc.)

Out of warranty period.

9. Wire Connection Diagram

Standard wire connection sequence:

Controller connector

Display connector (Female terminal) Display connector (Male terminal)

Figure 9-1 Wire Connection Diagram

Table 9-1 Standard connector wire sequence table

Standard Wire Sequence

Standard wire color

Function

1

Red (VCC)

Display power wire

2

Blue (Kp)

Controller power wire

3

Black (GND)

Display ground wire

4

Green (RX)

Display data reception wire

5

Yellow (TX)

Display data transmit wire

Some models are equipped with waterproof connectors and the color inside wires can not be seen.

10. Precautions

Pay attention to all the general operating when using the products and do not plug and unplug the display

while it is powered on.

Avoid bumping the display as much as possible.

Please do not change the parameter settings at will, otherwise normal riding cannot be guaranteed.

If display does not work properly, please send it to the repair center as soon as possible.

There may be differences between the physical products and this manual due to normal upgrade. Please

refer to the physical products.

Summary of Contents for YL81F





















Reviews: