York EVJC 12 Installation Instructions Manual Download

Page: 75 / 204

147

Designation of sensors

Faults

Indoor ambient temperature

The sensor is detected to be open-circuited or short-circuited for successive 30
seconds

Indoor tube temperature

The sensor is detected to be open-circuited or short-circuited for successive 30
seconds

Outdoor ambient temperature

The sensor is detected to be open-circuited or short-circuited for successive 30
seconds

Outdoor tube temperature

The sensor is detected to be open-circuited or short-circuited for successive 30
seconds, and no detection is performed within 10 minutes after defrost begins.

Exhaust

After the compressor has operated for 3 minutes, the sensor is detected to be
open-circuited or short-circuited for successive 30 seconds.

Overload

After the compressor has operated for 3 minutes, the sensor is detected to be
open-circuited or short-circuited for successive 30 seconds.

3. Other Controls
(1) ON/OFF

Press the remote button ON/OFF: the on-off state will be changed once each time you press the button.

(2) Mode Selection:

Press the remote button MODE, then select and show in the following ways: AUTO, COOL, DRY, FAN, HEAT, AUTO.

(3) Temperature Setting Option Button

Each time you press the remote button TEMP+ or TEMP-, the setting temperature will be up or down by 1

. Regulating

Range: 16~30

, the button is useless under the AUTO mode.

(4) Time Switch

You should start and stop the machine according to the setting time by remote control.

(5) 5. SLEEP State Control

a. When the air conditioner is under the mode of COOL, DRY, and the SLEEP mode has been set well, after the SLEEP
state keeps about 1 hour, the pre-setting T will raise 1

, and it will raise 1

again after 2 hours, so it raise 2

in 2 hours,

then it will run on at the setting temperature and wind speed.
b. When the air conditioner is under the mode of HEAT, and the Timer has been set well, after the SLEEP state keeps about
1 hour, the pre-setting T will reduce 1

, and it will reduce 1

again after 2 hours, so it reduce 2

in 2 hours, then it will

run on at the setting temperature and wind speed.
c. The setting temperature keeps the same under the FAN mode and AUTO mode.

(6) Indoor Fan Control

The Indoor Fan can be set as HIGH, MED, LOW by remote control, and the Indoor Fan will be respectively run at high,
medium, low speed. It will also be set as AUTO, and the Indoor Fan is as the followings at the automatic wind speed.
Cooling mode: T

ring

≥

setting

+ 2, high speed; T

setting

- 2

ring

setting

+ 2, medium speed; T

ring

≤

setting

– 2, low speed.

Sending wind mode: : T

ring

setting

+ 4, high speed; T

setting

≤

ring

≤

setting

+ 4, medium speed; T

ring

setting

+2, low

speed.
Moisture removal mode: force to be set as the low speed
Heating mode: T

ring

≤

setting

+ 1 high speed; T

setting

ring

setting

+ 5, medium speed; T

ring

≥

setting

+ 2, low speed.

(7) Buzzer Control

The buzzer will send a “Di” sound when the air conditioner is powered up or received the information sent by the remote
control or there is a button input, the single tube cooler doesn’t receive the remote control ON signal under the mode of
heating mode.

(8) Auto button

If the controller is on, it will stop by pressing the button, and if the controller is off, it will be automatic running state by
pressing the button, swing on and light on, and the main unit will run based on the remote control if there is remote control
order.

(9) Up-and-Down Swinging Control

When  power  on,  the  up-and-down  motor  will  firstly  move  the  air  deflector  to  o  counter-clockwise,  close  the  air  outlet.
After starting the machine, if you don’t set the swinging function, heating mode and auto-heating mode, the up-and-down
air deflector will move to D clockwise; under other modes, the up-and-down air deflector will move to L1. If you set the
swinging function when you start the machine, then the wind blade will swing between L and D. The air deflector has 7
swinging  states:  Location  L,  Location  A,  Location  B,  Location  C,  Location  D,  Location  L  to  Location  D,  stop  at  any
location between L-D (the included angle between L~D is the same). The air deflector will be closed at 0 Location, and the
swinging  is  effectual  only  on  condition  that  setting  the  swinging  order  and  the  inner  fan  is  running.  The  indoor  fan  and
compressor may get the power when air deflector is on the default location.

Operation