background image

5567611-BIM-B-1218

Johnson Controls Ducted Systems

7

Figure 4: ZV component location

Figure 4 shows the ZV-06 through -08 model. Table 1 lists the components of the unit.

Table 1: Component location table

Item

Description

Item

Description

A

Smart Equipment™ supply fan controls with IntelliSpeed™. Includes 
screw connectors for thermostat wiring and network connections

K

Power ventor motor

B

Disconnect location, optional disconnection switch

L

Two stage gas heating to maintain a warm, comfortable 
temperature

C

Filter access, 2-inch or 4-inch filter options

M

20-gauge aluminized steel tubular heat exchanger for long 
life. Stainless steel option

D

High efficiency sine wave fin evaporator coil

N

Intelligent control board for safe and efficient operation

E

ECM outdoor fan motor

O

Slide-out drain pan with 1-inch NPT connection

F

Micro-channel aluminum tube/aluminum fin condenser

P

Toolless door latch

G

Premium efficiency belt-drive blower motor

Q

Compressor access (High-efficiency 2-stage compressor)

H

Variable frequency drive

R

Base rails with forklift slots (three sides) and lifting holes

1

1. Roof curbs in eight-and fourteen-inch heights. Roof curbs to transition from a Ducted Systems ZD Series footprint to the ZV Series footprint 

are available as a field-installed accessory.

I

Solid core filter drier

S

Second model nameplate inside hinged access panel

J

Slide-out motor and blower assembly for easy adjustment and 
service

Summary of Contents for ZV-06
























































































Reviews: