background image

5567611-BIM-B-1218

64

Johnson Controls Ducted Systems

If there is a call for dehumidification and no call for cooling, the 
unit automatically reverts back to the normal hot gas reheat 
mode only allowing refrigerant stage one to run in reheat mode 
and refrigerant stage two remains off. 

If there is a call for dehumidification and a call for cooling, the 
unit remains in the alternate hot gas reheat mode allowing 
refrigerant stage one to run in hot gas reheat or 
dehumidification mode and refrigerant stage two runs in 
cooling.

Electric heating sequence of operations

The following sequence describes the operation of the electric 
heat section.

Two-stage heating:

a. When there is a call for first stage heat by the thermostat,

the heater relay (RA) is energized. After completing the
specified fan on delay for heating, the UCB energizes the
blower  motor.  If  the  second  stage  of  heat  is  required,
heater  relay  (RB)  is  energized.  After  completing  the
specified fan on delay for heating, the UCB energizes the
blower motor.

b The  thermostat  cycles  the  electric  heat  to  satisfy  the

heating requirements of the conditioned space.

Electric heat operation errors

Temperature limit

If the UCB senses zero volts from the high temperature limit, 
the indoor blower motor is immediately energized.

This limit is monitored regardless of unit operation status, that 
is, the limit is monitored at all times.

If the temperature limit opens three times within one hour, it 
locks on the indoor blower.

Safety controls

The UCB monitors the temperature limit switch of electric heat 
units.

The control circuit includes the following safety controls:

Limit switch

The limit switch (LS) is located inside the heater compartment 
and is set to open at the temperature indicated in Table 26, 

Electric heat limit setting, 

on page 64. It resets automatically. 

The limit switch operates when a high temperature condition 
caused by inadequate supply air flow occurs. This shuts down 
the heater and energizes the blower.

Reset

Reset removes the call for heating by lowering the thermostat 
setting lower than the conditioned space temperature.

Electric heat anticipator setpoints

The anticipator setpoint must be correct. Too high of a setting 
results in longer heat cycles and a greater temperature swing in 
the conditioned space. Reducing the value below the correct 
setpoint gives shorter ON cycles and may result in the lowering 
of the temperature within the conditioned space. See Table 27 
for the required electric heat anticipator setting.

Gas heating sequence of operations

When the thermostat calls for the first stage of heating, the low-
voltage control circuit from R to W1 is completed. A call for heat 
passes through the UCB to the ignition control board (ICB). The 
UCB monitors the W1 call and acts on any call for heat by 
monitoring the gas valve (GV). When voltage is sensed at the 
GV, the UCB initiates the fan on delay for heating, energizing 
the indoor blower when the specified delay has elapsed.

When the thermostat is satisfied, heating calls are ceased. The 
GV is immediately closed. The blower is de-energized after the 
fan off delay for heating has elapsed. The draft motor performs 
a 30-second post purge.

Ignition control board

First stage of heating

When the ICB receives a call for first stage of heating, “W1,” the 
draft motor is energized. Once the draft motor has been proven, 

Table 26: Electric heat limit setting

Unit (tons)

Voltage

Heater 

kW

Limit switch 

opens °F

ZV-06 (6.5) 
ZV-07 (7.5)
ZV-08 (8.5) 

208/230

9

150

18

150

24

150

36

150

ZV-10 (10) 

ZV-12 (12)

18

150

24

150

36

150

54

130

ZV-06 (6.5) 
ZV-07 (7.5)
ZV-08 (8.5) 

480

9

150

18

150

24

150

36

150

ZV-10 (10) 

ZV-12 (12)

18

150

24

150

36

150

54

130

Table 27: Electric heat anticipator setpoints

Setting, Amps

W1

W2

0.13

0.1

Summary of Contents for ZV-06
























































































Reviews: