background image

OPERATING & MAINTENANCE MANUAL                                                                                                                                MODEL :    EHA series 

 
 

YOUYANG  AIRPORT  LIGHTING  EQUIPMENT  INC.                                                          Page 

30/55 

4) Please stand up correctly the support part vertically using level tool. 

5) Please arrange after inspection of front & rear points of base plate to follow entry 

line. 

6) Please fasten bolt Nut after arrangement and the base plate position should not be 

changed during fastening. 

7) Please  lay on the  supporter  by  bolt loosing  of  turn-down  plate  of  fixing  plate  after 

support part installation work is finished. 

CAUTION: Please make a space for connection work of light fixture by support part which 

does not touch with ground.

 

8) Below work must be done before light fixture installation. 

- The light fixture must have Number for each bar and each mast has allocation. 

- Cut connection cable to light as instructed length. 

- Install cable & earth cable using feed cable work. 

9) Fasten loosely Bolt of coupling after cable connection to terminal of light and install 

light on the light fixture. 

10) Arrange Toe-in angle using level tool for horizontally 0 degree or, instructed angle. 

11)  Arrange  all  lights  as  instructed  angle  of  installation  section  for  vertical  angle  of 

each light. 

12) Light support Cable draw out through inside of support part to lower part outside. 

13) Input to inside of support for connection part of lights. 

14)  Fix  by  clamp  after  confirming  by  Level  tool  for  support  part  and  light  support  part 

should be vertical. 

15)  Taping  by  PVC  insulation  tape  and  EPR  tape  for  connection  parts  after  light  cable 

with secondary lead wire of Isolation transformer connection. 

16) Fix by bolt after support stand up. 

17) Please check installation work is well finished and clean site. 

 

 

 

 

 

 

Summary of Contents for EHA Series
























































Reviews: