background image

 

- 6 - 

 

WARNING 

Read and follow all instructions for assembly and operation.  Failure to properly assemble this 
equipment could result in serious injury to the user or bystanders, or cause equipment damage

 

20 TON DUAL ACTION LOG SPLITTER ASSEMBLY 

Set the shipping crate on a solid flat surface and carefully remove the lid. Use two people and take all 

parts out of the shipping crate and inspect the components to ensure there are no missing pieces 

before starting to assemble the log splitter follow steps 1 through 6. 

 

TOOLS REQUIRED 

 

Rubber or Wooden Hammer   

 

13mm, 17mm, 19mm Wrenches 

 

Large Adjustable Wrench   

 

Phillips Screw Driver 

 

Pliers 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 

 

 

 

Engine Shipped Without Oil. 

Before starting engine, fill with SAE 10W-30 motor oil. 
See engine manual for engine oil capacity. 
 

Hydraulic Oil Tank is Shipped Without Oil. 

When adding oil verify the oil level reads 1 from the top of hydraulic oil 
tank if marking is not shown fill to the neck. 
 

Inspect all Log Splitter Components. 

If you have damaged components:    Contact the freight company that 
delivered the log splitter and file a claim.

 

Summary of Contents for 23316

























Reviews: