background image

 

 

2

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 
 
 
 
 

 

 

 

 
REMOVE AND IDENTIFY LOOSE PARTS FROM CARTON AND BAG 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

SAFETY RULES 

 

READ THE DIRECTIONS BEFORE ASSEMBLY 

  Read the towing vehicle owners manual and towing vehicle safety rules. Know how to 

operate your tractor before using the tow-behind spreader. 

  Read the chemical label instructions and cautions for handling and applying the chemicals 

purchased for spreading. 

  Wear eye and hand protection when handling and when applying lawn or garden chemicals. 

  Never operate tractor and spreader attachment without wearing substantial footwear, and do 

not allow anyone to ride or sit on spreader attachment frame. 

  Never allow children to operate the tractor or spreader attachment, and do not allow adults to 

operate without proper instructions. 

  Always begin with the transmission in first (low) gear and with the engine at low speed, and 

gradually increase speed as conditions permit. 

  When towing spreader do not drive too close to a creek or ditch and be alert for holes and 

other hazards which could cause you to loose control of the spreader and tractor. 

  Before operating vehicle on any grade (hill) refer to the safety rules in the vehicle owner’s 

manual concerning safe operation on slopes. 

Stay off steep slopes!

 

Summary of Contents for YTL-002-162













Reviews: