background image

 

- 13 - 

 

STEP 11: Attach the Card Slot and Lock Support Tube 

 

1.  Insert the Ø3 R Pin (#16) into the safety pin on the hitch tongue. 
2.  Pull out the Ø3 R Pin (#16) before emptying the bed and then press the release pedal. 

 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 

 
 
 
 
 

WARNING 

Before using the utility dump cart, review the instructions below and safety information.    Failure to 
follow these instructions may result in property damage or injury to the operator or bystanders. 

 
 
USING YOUR UTILITY DUMP CART 

 

1. 

DO NOT

 exceed rated capacity of 500lb (226.8kg). 

2. 

ALWAYS

 secure and lock the utility cart to the vehicle hitch before operating. 

3. 

ONLY

 use approved vehicles when towing the dump cart (Lawn/Garden Tractors and ATVs) 

4. 

NEVER

 tow the utility dump cart with box raised. 

5. 

DO NOT

 over fill the utility dump cart.    Over flow loads can cause the cart and towing vehicle to 

lose traction and skid out of control. 

6. 

ONLY

 fill the dump cart to a comfortable dumping load.    Extremely heavy loads will be difficult to 

operate and dump. 

7. 

ALWAYS

 use the dump cart for its intended purpose. 

8. 

ALWAYS

  make  sure  that  the  tow  vehicle  and  the  combined  weight  of  the  operator  MUST  BE 

greater than the load of the cart weight for proper control. 

9. 

DO NOT

 use cart on public highways or roads. 

10. 

NEVER

 exceed 10mph when towing the dump cart. 

11. 

DO NOT

 make sharp turns that may cause the Lawn/Garden Tractor or ATV tires to rub against 

the utility dump cart. 

12. 

ALWAYS

 slow down before turning. 

13. 

ALWAYS

  use  caution  when  backing  the  utility  cart. 

To avoid the cart from “jack-knifing” always 

back up in a straight line. 

 

 
 
 
 

Operation Instructions 

Summary of Contents for YTL-010-757



















Reviews: