background image

GENERAL WARNINGS

IMPORTANT NOTE:

 All safety precautions and warnings, instructions, warranties 

and other collateral information are subject to change at the sole discretion of Yuneec. 
For the most up-to-date information please visit the corresponding product page at 
www.Yuneec.com or contact the nearest Yuneec office or authorized distributor.
The following special language terms are used throughout the product literature 
to indicate various levels of potential harm when operating this product:

NOTICE: 

Procedures, which if not properly followed, create a possibility of prop-

erty damage and/or little to no possibility of injury.

CAUTION: 

Procedures, which if not properly followed, create the probability of 

property damage and/or a possibility of serious injury.

WARNING: 

Procedures, which if not properly followed, create the probability 

of property damage, collateral damage and/or serious injury or create a high 
probability of superficial injury.

WARNING: 

Read the ENTIRE instruction manual to become familiar with the 

features of the product before operating. Failure to operate the product cor-
rectly can result in damage to the product, property and/or cause serious 
injury.

WARNING: 

This is a sophisticated consumer product. It must be operated 

with caution and common sense, and requires some basic mechanical ability. 
Failure to operate this product in a safe and responsible manner could result 
in damage to the product, property and/or cause serious injury. This product 
is not intended for use by children without direct adult supervision. Do not use 
with incompatible components or alter this product in any way outside of the 
instructions provided by Yuneec. The instruction manual contains instructions 
for safety, operation and maintenance. It is essential to read and follow all the 
instructions and warnings prior to assembly, setup and/or use in order to op-
erate the product correctly and avoid damage or serious injury.

WARNING: 

Failure to use this product in the intended manner as described in 

instruction manual can result in damage to the product, property and/or cause 
serious injury. This product is not a toy!

WARNING: 

As the user of this product you are solely and wholly responsible 

for operating it in a manner that does not endanger yourself and others or 
result in damage to the product or the property of others.

Do not expose the CGOET gimbal camera to water, including rain and mois-
ture.
Do not expose the lens of the CGOET gimbal camera to excessive light 
sources.
Do not operate the CGOET gimbal camera in environments with extremely 
high or low temperatures and high humidity.
Do not press the lens with excessive force.
Do not leave the camera with the lens facing the sun as rays of light from the 

sun may cause it to malfunction. Also, be careful when placing the camera 
outside or near a window.
Do not try to repair the CGOET gimbal camera by yourself.
Do not attempt to operate CGOET gimbal camera in areas with potential mag-
netic and/or radio interference including areas nearby broadcast towers, 
power transmission stations, high voltage power lines, etc.
Do not operate the Gimbal in the rain!
Do not expose the Gimbal to fire sources!
Do not touch or move the Gimbal until the initialization process has been 
completed.
In need of repair, send the CGOET gimbal camera to an authorized service center.

03

Summary of Contents for CGOET



























Reviews: