background image

 

Version 0.1 

8 June 2011 

www.2myhome.eu 

 

Technical Manual 

 

Caution:

 

-

 

This device is using a radio signal that passes through walls, windows and doors. The range is strongly 
influenced by local conditions such as large metal objects, house wiring, concrete, furniture, 
refrigerators, microwaves and similar items. On average, the indoor range is approximately 30 meters.  

-

 

Do not expose this product to excessive heat or moisture.  

-

 

Prevent long term exposure to direct sunlight. 

-

 

Do not attempt to repair this product. If the product is damaged or if you are in doubt about the 
proper operation, take the product back to the place of purchase.  

-

 

Do not clean the product with any liquid.

 

 

Normal operating voltage 

15VAC Power supply 

Frequency range 

868.42 MHz 

Range 

Up to 30m line of sight 

Storage temperature 

-5

°

C to +65

°

Storage humidity 

10% to 70% 

Operating temperature 

10

°

C to 50

°

Operating humidity 

30% to 80% 

 

Detailed information 

 

myGate

 

myGate

 is the central part of the home system. It will be connected (through a router) directly to Internet. The 

myGate

 controls Z-Wave devices, has a secure connection to the backoffice (e.g. 2MyHome) and runs with 

unique rules for every lifestyle which the end consumer had configured. Also the complete firmware of the  
Z-Wave module and microprocessor can be upgraded, which makes it a future proof system.  

Backoffice 

myGate

 connects automatically to the backoffice and creates a bi-directional tunnel between the backoffice 

and 

myGate

. This tunnel is secure with encryption and a frequently changing unique session key for every 

myGate

MyGate

 controls all Z-Wave nodes and has a caching mechanism which is necessary to also control 

battery operated devices which are not accessible directly. 

Configurations 

The rules in 

myGate

 are configured through the 2myHome User Interface, where the relations between every 

Z-Wave nodes are configured.  
 

Summary of Contents for myGate












Reviews: