OPERATION RANGE
* - 1-channel transmitters do not cooperate with roller blind controllers
CAUTION: The given range concerns open area - an ideal condition without any
natural or artificial obstacles. If there are some obstacles between a transmitter
and a receiver, it is advisable to decrease the range according to: wood and plas-
ter: from 5 to 20 %, bricks: from 10 to 40 %, reinforced concrete: from 40 to 80 %,
metal: from 90 to 100% , glass: from 10 to 20 %, Over- and underground medium
and high electrical power lines, radio and television transmitters, GSM transmit-
ters set close to a device system have also a negative influence on the range.
Symbol ROP-01 ROP-02 ROB-01 SRP-02 SRP-03 RWG-01 RWL-01 ROM-01 ROM-10 RDP-01 RTN-01
RNK-02
180 m
200 m
200 m
200 m
200 m
250 m
180 m
250 m
250 m
180 m
250 m
RNK-04
180 m
200 m
200 m
200 m
200 m
250 m
180 m
250 m
250 m
180 m
250 m
P-256/8
230 m
250 m
250 m
250 m
250 m
300 m
200 m
300 m
300 m
230 m
300 m
P-257/4 (2)
180 m
200 m
200 m
200 m
200 m
250 m
180 m
250 m
250 m
180 m
250 m
RNM-10
230 m
250 m
250 m
250 m
250 m
300 m
200 m
300 m
300 m
230 m
300 m
RNP-01
160 m
180 m
180 m
180 m
180 m
200 m
160 m
200 m
200 m
160 m
200 m
RNP-02
160 m
180 m
180 m
180 m
180 m
200 m
160 m
200 m
200 m
160 m
200 m
RNL-01
160 m
180 m
180 m
no*
no*
200 m
160 m
200 m
200 m
160 m
200 m
RTN-01
200 m
200 m
200 m
200 m
200 m
250 m
200 m
250 m
250 m
200 m
250 m
RCR-01
160 m
180 m
180 m
no*
no*
200 m
160 m
200 m
200 m
160 m
200 m
RTI-01
160 m
180 m
180 m
180 m
180 m
200 m
160 m
200 m
200 m
160 m
200 m
RXM-01
230 m
250 m
250 m
250 m
250 m
300 m
200 m
300 m
300 m
230 m
300 m
TIME PROGRAMMING
RADIO TRANSMITTERS DELETION
Press PROG push-button of RWG-01 device for a longer time till LED red diode switches
on (constant signal). Next release PROG push-button. Wait (for about 5 seconds) till LED
red diode switches on (first signal pulsates, next the signal is constant).
Press PROG push-button of RWG-01 device and then release it. LED red diode switches
off and then switches on (signal pulsates). Every LED diode pulse equals 1 second.
After the adjusted time is finished (the number of LED red diode flashes) press PROG
push-button and then release it - TIME IS ADDED.
Maximum time is 18 hours.
Press PROG push-button of RWG-01 device for a longer time.
After 5 seconds LED red diode switches on (signal pulsates) and then it switches off.
Release the push-button in RWG-01 - MEMORY IS DELETED.
GNIAZDO ZDALNIE STEROWANE Z PILOTEM P-257/2
RWG-01K
TECHNICAL DATA
P-257/2
RWG-01
Input rated voltage:
3 V (battery CR2032)
230 V AC
Battery life:
3 ÷ 5 years
-
Input voltage tolerance:
-
-15 ÷ +10 %
Nominal frequency:
-
50 / 60 Hz
Nominal power consumption:
-
0,29 W
Optic signalling of supply voltage:
-
LED green diode
Number of operation modes:
-
5
Number of channels:
2
1
Transmission:
radio 868,32 MHz
Coding way:
unidirectional
Coding:
addressing transmission
Maximum number of transmitters:
-
32
Range:
up to 250 m in the open area
up to 300 m in the open area
Time adjustment:
-
1 s ÷ 18 h (every second)
Optic signalling of transmitter’s
operation:
LED red diode
Relay contact parameters:
-
1NO 16A / 250V AC
AC1 4000 VA
Ambient temperature range:
-10 ÷ +55
o
C
Operating position:
free
Mounting:
-
230 V AC socket
Casing protection degree:
IP20 (PN-EN 60529)
Protection level:
III
II
Overvoltage category:
-
II
Pollution degree:
2
Surge voltage:
-
1 kV (PN-EN 61000-4-5)
Dimensions:
74 x 33 x 11,5 mm
160 x 66 x 90 mm
Weight:
0,020 kg
0,160 kg
Reference standard:
PN-ETSI EN 300 220-1
PN-ETSI EN 300 220-2
PN-EN 60669, PN-EN 60950
PN-EN 61000
DESCRIPTION
Remote control socket RWG-01 is used to connect any 230 V AC receiver of 4000 VA
and to wireless control by means of different EXTA FREE system transmitters. The
device can be mounted without any additional tools or interference in existing wiring - it
is directly mounted to 230 V AC socket.
