H. ZANDER GmbH & Co. KG • Am Gut Wolf 15 • 52070 Aachen • Germany
Tel +49 (0)241 9105010 • Fax +49 (0)241 91050138 •
info@zander-aachen.de • www.zander-aachen.de
1
Emergency Stop Safety Relay SR3C
M03
Ver. B
E61-137-00
Operating Instructions
English translation
Errors and technical changes reserved
•
2 start behaviors possible:
- Monitored manual start
- Automatic start
•
Short circuit and earth fault monitoring
•
Up to PL e, SILCL 3, category 4
The SR3C is a universal emergency stop safety switching device
with three safe relay contactss that can quickly and safely stop
the moving parts of a machine or system in case of danger.
Applications for the SR3C include single or dual-channel emer-
gency stop circuits and guard monitoring on machines and
plants.
•
3 safe, redundant relay contacts
1 auxiliary contact (signaling contact)
•
Connection of:
- Emergency stop buttons
- Safety switches
- Non-contact safety switches
- OSSD-Outputs
•
Single and dual-channel operation possible
•
Feedback loop for monitoring downstream contactors or
expansion modules
•
Cyclical monitoring of the output contacts
•
Indication of the switching state via LED
Function
The emergency stop safety switching device SR3C is
designed for safe isolation of safety circuits according to
EN 60204-1 and can be used up to safety category 4, PL e
according to EN ISO 13849-1.
The internal logical system closes the safety contacts when
the start button is pressed.
If the safety switch is opened, the positively driven safety
contacts are opened and safely switch the machine off. It is
ensured that a single fault does not lead to a loss of the
safety function and that every fault is detected by cyclical
self-monitoring no later than when the system is switched
off and switched on again.
Electrical
Connection
•
Consider the information in the section "Techn. data"
•
When the 24 V version is used, a safety transformer
according to EN 61558-2-6 or a power supply unit with
electrical isolation from the mains must be connected.
•
External fusing of the safety contacts must be provided
•
If the device does not function after commissioning, it
must be returned to the manufacturer unopened. Ope-
ning the device will void the warranty
•
Use adequate protective circuit for inductive loads (e.g.
free-wheeling diode)
Installation
As per EN 60204-1, the device is intended for installation in
control cabinets with a minimum degree of protection of
IP54. It is mounted on a 35 mm DIN rail according to
DIN EN 60715 TH35.
Safety
Precautions
Fig. 1 Block diagram SR3C
Fig. 2 Installation / removal
Fig. 3 Connections
A1:
Power supply
A2 :
Power supply
S11:
DC 24 V control voltage
S10:
Control line
S21:
Start control line
S13:
Control line
S14:
Control line
S12:
Control line
13-14:
Safety contact 1
23-24:
Safety contact 2
33-34:
Safety contact 3
41-42:
Auxiliary contact
•
All relevant safety regulations and standards are to be
observed.
•
The overall concept of the control system in which the
device is incorporated must be validated by the user.
•
Failure to observe the safety regulations can result in
death, serious injury and serious damage.
•
Note down the version of the product (see label “Ver: x”)
and check it prior to every commissioning of a new de-
vice. If the version has changed, the overall concept of
the control system in which the device is incorporated
must be validated again by the user.
•
Installation and commissioning of the device must be
performed
only by authorized personnel
.
•
Observe the country-specific regulations when installing
the device.
•
The electrical connection of the device is only allowed to
be made with the device isolated.
•
The wiring of the device must comply with the instruc-
tions in this user information, otherwise there is a risk
that the safety function will be lost.
•
It is not allowed to open the device, tamper with the
device or bypass the safety devices.
Correct Use
Germanischer Lloyd
Certifikat TAE00003JF
