41
Mod. ITACA-TROIA rev 01
Instructions for use
translated from the original text
IT
IT
FR
FR
ES
ES
EN
EN
Saturday and Sunday (SS).
The lit segment at the bottom of display D2 indicates the ON
time:
- - - -
1 I
M o
The lit segment at the top of display D2 indicates the OFF
time:
- - - -
1 I
M o
For each program, you must set the ON and OFF time.
DESCRIPTION
DISPLAY
1) Use K3/K7 to scroll through to
the desired sub-menu and press K5.
G i o r n
2) Press K3/K7 to select one of the
three programs available
- - - -
1 I
M o
3) Press K4 for 3 seconds
0 0 . 0 0
1 I
M o
4) Select the ignition time
5) Press K5 to edit: the selected
value (hours or minutes) will flash.
Press K5 to go from hours to mi-
nutes and vice-versa; K3/K7 to edit
the value.
0 1 . 0 0
1 I
M o
6) Press K5 to save the set value
2 1 . 3 0
1 I
M o
7) Press K3 to select the OFF time
and repeat the above procedure
from point 5
0 0 . 0 0
1 I
M o
For each programming slot, it is possible to change the mi-
nutes at quarter of an hour intervals (example: 20.00, 20.15,
20.45).
Only if you set the hour value at 23 is it possible to increase
the minutes from 45 to 59 for ignition between midnight.
Midnight Programming: set a programming slot for a day of
the week, the OFF time on 23:59. For a subsequent weekday
programming slot, set the ON time on 00:00.
Example
Monday Chrono Programming
ON
2 2 . 0 0
1 I
M o
2 3 . 5 9
1 I
M o
OFF
Tuesday Chrono Programming
ON
0 0 . 0 0
1 I
T u
0 7 . 0 0
1 I
T u
OFF
4.3.4
CLOCK (OROL)
Enables you to set the current date and time. The top display
shows the hours and minutes, whereas the bottom one shows
the day of the week.
INSTRUCTIONS
DISPLAY
Press K5 to edit. The value selected
(hours, minutes, day) flashes. Edit the
value by pressing K3/K7. Press the key
or K5 to edit the other parameters.
Press K5 again to save the set value
0 7 . 3 3
M o
5 ROUTINE CLEANING
All the parts must be cleaned up when the
stove is completely cold and unplugged.
The product does not require much mainte-
nance if certified quality pellets are used.
5.1
DAILY/WEEKLY CLEANING
5.1.1
CLEANING BEFORE EACH IGNITION
Clean the brazier from ashes and any encrustation that can
obstruct the air passageways. If the pellets run out, unburnt
pellets could accumulate inside the brazier. Always empty the
brazier from residue before each ignition.
fig. 32 clean brazier dirty brazier
REMEMBER THAT ONLY A CORRECTLY CLEANED BRAZIER
CAN GUARANTEE PERFECT IGNITION AND OPERATION OF
YOUR PELLET PRODUCT.
When good quality pellets are used, it is normally sufficient
to use a brush to restore the brazier to ideal operating con-
ditions.
After a long idle period,
using a vacuum cleaner with a long
tube
, remove any pellet residue sitting for a long time as it
could have absorbed humidity thus modifying its original
characteristics and becoming unsuitable for combustion.
5.1.2
CHECK EVERY 2/3 DAYS
Inspect and clean the combustion chamber. Clean and empty
the ash pan, paying attention to hot ashes.
Only if the ashes
are completely cold
may you use a vacuum cleaner to remo-
ve them. In that case, use a vacuum cleaner suitable to vacu-
um particles of a certain size. Your own experience and the
quality of the pellets will determine the frequency of cleaning.
It is however recommended not to go beyond 2 or 3 days.
When the operation is finished, reinsert the ash pan below the
brazier making sure it is properly in place.
5.1.3
CLEANING THE GLASS
To clean the ceramic glass, we recommend using a dry brush
or, in case of encrustations, a small amount of a specific spray
detergent Then clean with a dry cloth.
Summary of Contents for ITACA
