background image

3

1.

Hob Top

2.

Powered Rapid Burner

3.

Semi-rapid Burners

4.

Auxiliary Burner

5.

Control knob for back right burner (semi-rapid)

6.

Control knob for back left burner (semi-rapid)

7.

Control knob for front left burner (powered rapid)

8.

Control knob for front right burner (auxiliary)

9.

Automatic ignition pushbutton

1

3

2

3

Description of the Hob

5

6

7

8

4

9

Installation

Any  gas  installation  must  be  carried  out  by

qualified personnel, and in accordance with existing

rules and regulations.

The relevant instructions are to be found in the

second section of this manual.

Please,  ensure  that,  once  the  appliance  is

installed, it is easily accessible for the engineer

in the event of a breakdown.

WHEN THE HOB IS FIRST INSTALLED

Once the hob has been installed, it is important

to remove any protective materials, which were

put on in the factory.

THE HOB LID

In order to make the appliance match with the

kitchen design, a lid can be fitted on the hob.

- The lid (available on request) is meant to avoid dust

to settle on the hob, when it is closed, and to collect

splashes of oil or fat, when it is open. Do not use it for

any other purpose.

- Always wipe off any splash of liquid before opening

the lid.

- Always clean the lid from cooking residues before

opening it or taking it off.

WARNING! The crystal lid can splinter when

overheated. Always ensure all the burners are

off before closing it.

Summary of Contents for PNL49









Reviews: