background image

4

INSTALLATION

It is mandatory that all operations required for the
installation be carried out by QUALIFIED
PERSONNEL in accordance with existing rules
and regulations.

The appliance must be installed in accordance
with " X " specification (EN60.335-2.6). The
cooker must not be installed higher than the
worktop.

Please ensure that when the appliance is
installed it is easily accessible for the
engineer in the event of a breakdown.

Before your appliance is connected to the mains
electricity supply, check to ensure that the voltage
and the frequency shown on the rating plate
corresponds with your supply voltage.

This appliance must be earthed.

Before installation ensure that the local distribution
conditions (gas type and pressure) and the pre-
setting of the appliance are consistent.

This appliance must not connected to a chimney.
It has to be installed and connected in
accordance with the rules in force. Special
attention should be paid to the applicable
disposal concerning ventilation.
The adjusting conditions of this appliance are
mentioned on the rating plate.

Connection to gas supply.

Check that the gas flow and the diameter of the
supply pipe is sufficient to supply all the
appliances of the installation

.

  Check that all connections are tight.

  Install an accessible and visible gas tap to

isolate the appliance.

LOCATION

The cooker has been registered as a “Class
X”appliance according to Fire Rick Regulations.
Any adjacent cabinets or walls must not exceed
the cooker’s height.
The cooker may be located in a kitchen, a
kitchen/diner or bed sitting room, but not in a
bathroom or shower room.

The minimum distance combustible material can
be fitted above the cooker in line with the edges
of the cooker is 69 cm (see fig.)

 

The appliance must be set on a

heatproof floor. The adjustable feet must not
be removed.

Levelling

The appliance is provided with adjustable small
feet placed in the back and front corners of the
base.

By adjusting the small feet it is possible to
change the height of the appliance so as to
ensure a better levelling with other surfaces and
an even distribution of the liquids contained in
pots and pans.

2 cm

2 cm

62 cm

69

cm

2 cm

2 cm

69cm

15 cm

                   

Summary of Contents for ZCC 5607






















Reviews: