background image

3

Hob Burners Control Knobs

The hob burners control knobs are situated on the hob
front panel. The symbols on the knobs mean that :

there is no gas supply

 

there is maximum gas supply

  

there is minimum gas supply

Lighting the Burners

• For easier lighting, proceed before putting a pan

on the pan support.

Push the relevant knob down and turn it anti-clockwise
until it reaches the "maximum" position.

After lighting the flame, keep the knob pushed down for

about 5 seconds. This will allow the "thermocouple" (Fig.

1 lett. D) to be heated and the safety device to be

switched off, otherwise the gas supply would be
interrupted. Then, check the flame is regular and adjust
it as required.
If you cannot light the flame even after several attempts,
check the "cap" (Fig. 1 -  lett. A) and the "crown" (Fig. 1
- lett. B) are in the correct position. To put the flame out,
turn the knob to the symbol 

.

In the absence of electricity, ignition can occur without
the electrical device; in this case approach the burner
with a flame, push the relevant knob down and turn
it anti-clockwise until it reaches the "maximum"
position.

• Always turn the flame down or put it out before

taking the pans off the burner.

Using the hob correctly

To ensure maximum burner efficiency, it is strongly
recommended that you use only pots and pans with a
bottom fitting the size of the burner used, so that flame
will not spread beyond the bottom of the vessel (see the
table beside).

It is also advisable, as soon as a liquid starts boiling, to
turn down the flame so that it will barely keep the liquid
simmering.

Use only pans or pots with flat bottom.

Carefully supervise cookings with 

fats or oil

,

since these types of foodstuff can result in a fire,
if over-heated.

Burner

minimum

maximum

diameter

diameter

Triple Crown

180 mm.

260 mm.

(ultra rapid)
Big (rapid)

180 mm.

260 mm.

Medium (semirapid)

120 mm.

220 mm.

Small (auxiliary)

80 mm.

160 mm.

Fig. 1

Contents

FO 0204

This appliance complies with the following
E.E.C. Directives:

- 73/23

 - 

90/683

 (Low Voltage Directive);

- 89/336

 (Electromagnetical Compatibility Directive);

-

90/396

 (Gas Appliances)

- 93/68

 (General Directives)

and subsequent modifications.

MANUFACTURER:

ELECTROLUX HOME PRODUCTS ITALY S.p.A.
Viale Bologna 298 - 47100 FORLI’ (Italy)

Instruction for the User

Important Safety Information

2

Instruction for the User

3

Maintenance and Cleaning

4

Service and original spare parts

5

Technical Data

5

Instruction for the Installer

6

Electrical connection

7

Adaptation to different types of gas

8

Building In

9

For the User

For the Installer

Summary of Contents for ZGF 78 ICX












Reviews: