background image

8

Injectors replacement

• Remove the pan supports.

• Remove the burner's caps and crowns.

• With a socket spanner 7 unscrew and remove the

injectors (Fig. 8), and replace them with the ones
required for the type of gas in use (see 

Table 2

).

• Reassemble the parts, following the same procedure

backwards.

• Replace the rating label (placed near the gas supply

pipe) with the relevant one for the new type of gas
supply. You can find this label in the package of the
injectors supplied with the appliance.

Should the feeding gas pressure be different or variable
compared with the required pressure, an appropriate
pressure adjuster must be fitted on the gas supply pipe,
in compliance with the rules in force.

Fig. 8

FO 0392

Adjustment of minimum level

To adjust the minimum level of the burners, proceed as
follows:

• Light the burner.

• Turn the knob on the minimum position.

• Remove the knob.

• With a thin screwdriver, adjust the by-pass screw

(see Fig. 9). If changing from natural gas to LPG,
completely tighten clockwise the screw, until a small
regular flame is obtained.

• Finally check the flame does not go out when quickly

turning the knob from the maximum position to the
minimum position.

This procedure can easily be carried out, anyhow the
hob has been positioned or built in the working top.

  Burner

Ø By-pass

in 1/100

of mm.

  Auxiliary

28

  Semi-rapid

32

  Rapid

40

  Ultra rapid

56

Table 1 : BY-pass diameters

Table 2: Injectors

Fig. 9

By-pass screw

TYPE

TYPE OF

INJECTORS

NOMINAL

REDUCED

NOMINAL

NOMINAL

OF GAS

BURNER

MARKS

POWER

POWER

POWER

PRESSURE

1/100 mm

INPUT

kW

mbar

KW

m3/h

g/h

Ultra-rapid (large)

146

4,00

1,20

0,381

-

Rapid (large)

113

2,80

0,65

0,267

-

Semi-rapid (medium)

96

2,00

0,45

0,190

-

20

Auxiliary (small)

70

1,00

0,33

0,095

-

Ultra-rapid (large)

98

4,00

1,20

-

288

Rapid (large)

86

2,80

0,65

-

202

Semi-rapid (medium)

71

2,00

0,45

-

144

28-30/37

Auxiliary (small)

50

1,00

0,33

-

72

Ultra-rapid (large)

146

3,00

1,20

0,285

-

Rapid (large)

108

2,13

0,52

0,210

-

Semi-rapid (medium)

105

1,72

0,42

0,186

-

13*

Auxiliary (small)

80

0,90

0,30

0,085

-

NATURAL

GAS
G 20

LPG

(Buthane/

Propane)

Adaptation to different types of gas

NATURAL

GAS
G 20

* for Russia only.

Summary of Contents for ZGF 78 ICX












Reviews: