background image

REPLACEMENT OF THE CONNECTION

CABLE

The replacement of electric cable must

be carried out exclusively by the

service force centre or by personnel

with similar competencies, in

accordance with the current

regulations.

To replace the connection cable use

only H03V2V2-F T90 or equivalent

type. Make sure that the cable section

is applicable to the voltage load and

the working temperature. The yellow/

green earth wire (B) must be

approximately 2 cm longer than the

live and neutral wire (A).

A

B

1. Connect the green and yellow (earth) wire to

the terminal which is marked with the letter 'E',
or the earth symbol  , or coloured green and

yellow.

2. Connect the blue (neutral) wire to the terminal

which is marked with the letter 'N' or coloured

blue.

3. Connect the brown (live) wire to the terminal

which is marked with the letter 'L'. It must

always be connected to the network phase.

There must be no cut or stray strands of wire

present. The cord clamp must be correctly

attached to the outer sheath.

ASSEMBLY
1.

2.

3.

min. 55 mm

min. 650 mm

560 mm

min. 100 mm

30 mm

480 mm

min. 600 mm

4.

50 mm

400 mm

13

Summary of Contents for ZGX65414





















Reviews: