background image

8

SOMETHING NOT WORKING

SERVICE AND SPARE PARTS

If, having followed these instructions carefully, your cooker hood fails to work properly please carry out
the following checks.

Symptom

The cooker hood will not start

The cooker hood is not working effectively

The  cooker  hood  has  switched  off  during
operation

If after all these checks, the problem persists,
contact your local Service Force Centre,
quoting the model and serial number.

Please note that it will be necessary to
provide proof of purchase for any
in-guarantee service calls.

Solution

• Check the hood is connected to the electricity supply.
• Check that the fan speed control is set to 1, 2 or 3.

• The fan speed is set high enough for the task.
• The grease filter is clean.
• The kitchen is adequately vented to allow the entry

of fresh air.

•  If set up for recirculation, check that the charcoal

filter is still effective.

• If set up for extraction, check that the ducting and

outlets are not blocked.

• The safety cut-out device has been tripped.
• Turn off the hob and then wait for the device to reset.

In-guarantee customers should ensure
that the above checks have been made as
the engineer will make a charge if the fault
is not a mechanical or electrical
breakdown.

If  you  require  an  engineer  or  wish  to  purchase  spare
parts contact your local Service Force Centre by
telephoning:

08705 929929

Your telephone call will be routed to your local
Service Force Centre. For further details please see the
accompanying customer care book.

For  general  assistance  with  your  appliance  or  for
information  on  Zanussi  products  please  contact  our
Customer Care Department.

Customer Care Department,
Zanussi
55-77 High Street
Slough
Berkshire
SL1 1DZ

Tel: 08705 727 727*

* calls  to  this  number  may  be  recorded  for  training

purposes.

Summary of Contents for ZH 280





















Reviews: