background image

8

Technical Specifications

Model

ZHC 955

Dimensions (in cm):

Height

81,5 - 112,5

Width

89,8

Depth

50,1

Maximum absorbed power:

200 W

Motor absorption:

170 W

Lighting:

2 x 20 W

Length of the cable:

150 cm

Electrical connection:

220-240 V

Fuse rating:

5A T

Subject to change without notice.

What to do if

If your appliance fails to work properly please carry out the following checks.

Symptom

Solution

The cooker hood will not start...

Check  that: The hood is connected to the electricity supply.
Check that a fan speed has been selected

The cooker hood is not working

Check that: The fan speed is set high enough for the task.
The grease filters are clean.
The kitchen is adequately vented to allow  the entry of fresh air.
If set up for recirculation, check that the charcoal filter is still effective.
If set up for extraction, check that the ducting and outlets are not
blocked.

The cooker hood has

The safety cut-out device has been tripped.

switched off during operation...

Turn off the hob and then wait for the device to reset.
If the hood has been installed below the heights indicated in the
installation instructions the motor will cut-out frequently which will
damage the hood.

If after all these checks, the problem persists, contact your local Service Force Centre, quoting the model and
serial number.
Please note that it will be necessary to provide proof of purchase for any in-guarantee service calls.
In-guarantee customers should ensure that the above checks have been made as the engineer will make a
charge if the fault is not a mechanical or electrical breakdown.

Special Accessories

Charcoal Filter Type 20

Summary of Contents for ZHC 955

















Reviews: