background image

11

TECHNICAL SPECIFICATIONS

DIMENSIONS

Height

85

cm

Width

49.5

cm

Depth

60

cm

POWER SUPPLY VOLTAGE AND FREQUENCY

220-240 V / 50 Hz

TOTAL POWER ABSORBED

100 W

AVERAGE DAILY UNITS ELECTRICITY(*)

0,55 kWh

GROSS CAPACITY

140 l

NET CAPACITY

136 l

(*)This figure is based on standard test results in accordance with European Standard EN153. Actual
consumption will depend on how the appliance is used and where it is located.

INSTALLATION

D200

50-100 mm

10 mm

10 mm

A

B

NP006

Positioning

For this appliance to work efficiently, it must not be
located where the temperatures will fall below 10°C
(50°F) or rise above 32°C (90°F), e.g. conservatories.

For correct operation this appliance must be located in
a dry atmosphere, away from heat sources, e.g.
cookers, radiators, boilers and direct sunlight.

You should also ensure that air can circulate freely
around the back and the top of the cabinet. There
should be 100mm (4”) between the top of the cabinet
and any overhanging kitchen furniture. Alternatively
allow 50mm (2”) between the top of the cabinet and
any overhanging kitchen furniture and a gap of 25mm
(1”) on either side of the appliance.

Do not obstruct the space underneath. The back of the
cabinet may be placed close to the wall but must not
touch it. DO NOT install in places with restricted
ventilation.

Adjust the level of the appliance by screwing out the
adjustable foot, or feet, at the bottom of the cabinet
using your fingers.

Summary of Contents for ZL 25 W

















Reviews: