Zanussi ZLA 99 W Instruction Booklet Download

Page: 5 / 20

OPERATION

Before using

Remove all securing tapes. Wash inside the
appliance with lukewarm water and bicarbonate of
soda (5 ml to 0.5 litre of water).

Do not use soap or detergent as the smell may
linger. Dry thoroughly.

Setting the temperature

The temperature inside the refrigerator is regulated
by a thermostat with different temperature positions
and an “OFF” (O) position.

Position

●

= minimum coldness

Position

●

= maximum coldness

Turn the thermostat control knob to the required
position.

The thermostat setting can vary as the temperature
inside the refrigeration compartment depends on the
following factors:

– room

temperature

– how often the door is opened

– how much food is stored

– position of the appliance

Fresh food refrigeration

To obtain the best performance, do not store warm
food or evaporating liquids in the refrigerator; do
cover or wrap the food, particularly if it has a strong
flavour.

Do not cover the shelves with any protective
material, such as paper, cardboard or plastic, which
may obstruct the air circulation through them.

To help you use your refrigerator correctly, here are
some more useful hints:

Raw meat (beef, pork, lamb & poultry or chicken):
wrap in polythene bags and place on the glass shelf
above the salad crispers.

Meat can only be stored safely in this way for
one or two days at the most.

Fruit & vegetables: these should be thoroughly
cleaned and placed in the bottom salad crisper(s).

Butter & cheese: these should be placed in special
airtight containers or wrapped in aluminium foil or
polythene bags to exclude as much air as possible.

Milk bottles: these should have a cap and should be
stored in the bottle rack on the door.

Control panel

A - Pilot light

B - Thermostat control

To Start the Appliance

Allow the appliance to stand for 2 hours after
installation.

Plug in the appliance and switch on at the mains
supply. Turn the thermostat control knob (B) to a
medium setting. The pilot light (A) will illuminate.
Leave the appliance for approximately 4 hours to
allow the correct temperature to be reached before
placing food inside.

To switch off the appliance turn the thermostat
control knob to position “O” .

Important

During prolonged periods of abnormally hot weather,
if the thermostat is set on too high a number, the
cooling system may operate continuously and the
fridge cooling plate may not defrost. Turning the
knob to a lower number will cause the automatic
defrosting to resume.

Door reversal directions

1. Disconnect from the electricity supply.

2. Gently lay the fridge on its back with the top held

away from the floor by 5-8 cm (2-3 inches) of
packing;

3. Remove the ventilation grill (D).

4. remove the bottom hinge (E) by unscrewing its

three fixing screws;

5. Slide out the fridge door from pin (G), unscrew

the latter and then refit it on the opposite side;

6. remove the two plugs of the door (where

available), discovering the holes for the hinge
pins, assemble them on the opposite side;

7. using a 10 mm spanner, unscrew the hinge pin

(E) and reassemble it on the opposite side of the
hinge;

8. reassemble the lower hinge (E) on the opposite

side, using the screws previously removed. Slide
the hole cover (F) out of the ventilation grille (D)
by pushing it in the direction of the arrow and
reassemble it on the opposite side;

9. reassemble the door;

10.refit the ventilation grille (D), clipping it into place;

11. Unscrew the handle. Refit it on the opposite side

after having pierced the plugs with a punch.
Cover the holes left open with the plugs supplied
in the documentation pack.

Important

After completion of the door reversing operation,
check that the door gasket adheres to the cabinet. If
the ambient temperature is cold (i.e. in Winter), the
gasket may not fit perfectly to the cabinet. In that
case, wait for the natural fitting of the gasket or
accelerate this process by heating up the part
involved with a normal hairdryer on a low setting.

D162/a

PR18

Printed on recycled paper