Zanussi ZWH 6125, User Manual

When these buttons are pressed, the corresponding pilot

lights illuminate. When they are pressed again, the pilot

lights go out. If an incorrect option is selected, the inte-

grated red pilot light of the button 7 flashes 3 times and

the message Err is displayed.

For the compatibility among the washing programmes

and the options see chapter «Washing programmes» .

Start the programme by pressing button 7

To start the selected programme, press this button; the

corresponding green pilot light stops blinking.

The pilot light 9 illuminates to indicate that the appliance

starts operating and the door is locked.

If you have chosen a delayed start, the machine will begin

the countdown.
Important!  If an incorrect option is selected, the message

Err

  is displayed for a few seconds and the red pilot light

of this button blinks 3 times.

Select the Delay Start by pressing button 8

Before you start the programme, if you wish to delay the

start, press this button to select the desired delay.

The selected delay time value will appear on the display

for a few seconds, then the duration of the programme

will appear again.

You must select this option after you have set the pro-

gramme and before you start the programme.

You can cancel or modify the delay time at any moment,

before you press button 7 .

Selecting the delay start :
1. Select the programme and the required options.
2. Select the delay start by pressing button 8 .
3. Press button 7 :

- the machine starts its hourly countdown.

- the programme will start after the selected delay has

expired.

Cancelling the Delay Start after having started the pro-

gramme:
1. Set the washing machine to PAUSE by pressing but-

ton 7 .

2. Press button 8 once. On the display will appear   ' .
3. Press button 7 again to start the programme.
Important! 
• The selected delay can be changed only after selecting

the washing programme again.

• The door will be locked throughout the delay time. If

you need to open the door, you must first set the wash-

ing machine to PAUSE by pressing button 7 and wait

a few minutes before opening the door. After you have

closed the door, press the same button again.

Important!  The Delay Start cannot be selected with

DRAIN programme.

Altering an option or a running programme

It is possible to change some options before the pro-

gramme carries them out.

Before you make any change, you must pause the washing

machine by pressing button 7 .

Changing a running programme is possible only by re-
setting it. Turn the programme selector dial to   and

then to the new programme position. Start the new pro-

gramme by pressing button 7 again.

The washing water in the tub will be not emptied out.

Interrupting a programme

Press the button 7 to interrupt a programme which is

running, the corresponding pilot light starts blinking.

Press the button again to restart the programme.

Cancelling a programme

Turn the selector dial to   to cancel a programme which

is running. Now you can select a new programme.

Opening the door after the programme has started

First set the machine to pause by pressing the button 7 .

If the pilot light 9 blinks and after a few minutes goes off,

the door can be opened.

If the pilot light 9 remains lit, this means that the machine

is already heating or that the water level is too high. In

any case, do not try to force the door!

If you cannot open the door but you need to open it, you

have to switch the machine off by turning the selector dial
to   . After a few minutes the door can be opened

(Pay attention to the water level and temperature!).

After closing the door, it is necessary to select the pro-

gramme and options again and to press button 7 .

At the end of the programme

The machine stops automatically. The blinking   appears

on the display, the pilot light of button 7 and the pilot light

9 go off.

If a programme or an option that ends with water left in

the tub has been selected, the pilot light 9 remains on and

the door is locked to indicate that the water must be emp-

tied out before opening the door.

Follow the below instructions to empty out the water:

12