background image

Zaxcom ZFR 200 / 

300 Manual____   _______________                      ___ ___

Extended Menu

 

 

14 

 

 

IFB Receive Pulse 

 

this menu will only appear if IFB is set to go into transmit mode.

 

 

IFB RX PULSE: 

NEVER

   

 

 

 

 

IFB RX PULSE: 

120 SECS

   

 

 

 

 

 

 

 

This is where you set how often the ZFR will search for Timecode while operating.  

When enabled this tells the ZFR to leave ZaxNet transmit mode once every XX seconds to go into 

receive mode so it can re-jam its timecode wirelessly via ZaxNet. This has no affect on the UHF audio 

transmission.   

 

The settings are 

NEVER

 or any interval between 

10

 and 

999

 seconds.  

 

 

 

Power-Up Mode 

 

POWER UP 

MODE: LOCKED 

 

This page determines if the keys will lock after power-up. 

 

LOCKED

 – After power-up has completed, the ZFR will automatically go into 

Lock Mode

 to 

prevent accidental changes to the settings.  

 

UNLOCKED 

– The keys are unlocked upon power-up. You can always lock the keys by going in to 

the 

Lock Screen

 in the Main Menu. 

 

Unlocking the ZFR 

 Simultaneously press the 

MENU

 and 

INC

 

keys

.   

Format Recording Card  

 

 

 

 

 

This page erases and formats the micro SD card.  All cards must be formatted before it can be used.  

 

 

PRESS UP KEY 5X 
TO ERASE CARD 

NOTE:

 When the ZFR searches for TC it will temporally go out of transmit mode for 

approximately 1 second as it receives a TC signal.  

The TRX will stay in transmit mode and never go 

into receive mode. 

 

 

The ZFR will go out of transmit mode every 

10 Minutes 

 

Note:

  You would need to use this setting if 

you are monitoring audio via an ERX receiver 

and you still want the ZFR to update TC

 

 

 

 IFB RX PULSE: 
 NEVER 

 IFB RX PULSE: 
 600 SECS 

 

POWER UP 

 MODE: LOCKED 

 

PRESS UP KEY 5X 

 TO ERASE CARD 

Summary of Contents for ZFR200






























Reviews: