background image

zBOOST

®

 SOHO YX560P USER GUIDE

i

 

About zBoost

®

 from Wi-Ex

®

Wi-Ex

the leader

 in cell phone signal boosters manufactures zBoost, the award-winning line 

of cell phone signal boosters that enhance the performance of your cell phone, smartphone 

and wireless data card.

Patented technologies

 protect the carrier network.

zBoost products 

have more awards, more sales and more locations than all other signal 

boosters…COMBINED.

FCC Information

FCC ID: SO4YX545-PCS-CEL2

Warning: 

Changes or modifications to this device not expressly approved by Wi-Ex® could void the 

user’s authority to operate the equipment.

Note: 

This equipment has been tested and found to comply with the limits for a Class B digital 

device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable 

protection against harmful interference in a residential installation. This equipment generates, 

uses, and can radiate radio frequency energy and, if not installed and used in accordance with 

the instructions, may cause harmful interference to radio communications. However, there is no 

guarantee that interference will not occur in a particular installation. If the equipment does cause 

harmful interference to radio or television reception, which can be determined by turning the 

equipment off and on, the user is encouraged to try to correct the interference by one or more of the 

following measures:

• 

Reorient or relocate the receiving antenna

• 

Increase the separation between the equipment and receiver

• 

Connect the equipment to an outlet on a circuit different from that to which the receiver is 

connected

• 

Consult the dealer or an experienced radio/TV technician for help

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled 

environment. This transmitter must not be co-located or operating in conjunction with any other 

antenna or transmitter. In accordance with FCC requirements of human exposure to radiofrequency 

fields, the radiating element (antenna) shall be installed such that a minimum separation distance of 

20cm (8in) is maintained from all persons.

Industry Canada Regulations

IC ID: 5544A-YX545PCSCL2

This Class B digital apparatus meets all requirements of the Canadian Interference Causing 

Equipment Regulations. Operation is subject to the following two conditions: (1) this device may not 

cause harmful interference, and (2) this device must accept any interference received, including 

interference that may cause undesired operation.

The term “IC:” before the radio certification number only signifies that Industry Canada technical 

specifications were met.

RF Exposure: The manufacturer’s rated output power of this equipment is for single carrier 

operation. For situations when multiple carrier signals are present, the rating would have to be 

reduced by 3.5 dB, especially where the output is re-radiated and can cause interference to 

adjacent band users. This power reduction is to be by means of input power or gain reduction and 

not by an attenuator at the output of the device.

Summary of Contents for SOHO YX560P












Reviews: