background image

Start of Configuration

RESET

 The reading of the "RESET” label

turns all the parameters back to
default values.

 

When you intend to turn your

scanner back to default
parameter, please scan the
"Start of configuration" label first,
then scan "RESET" label 

and

finally scan the "End of
configuration" label.

ABORT

RS-232C

PC/AT

WAND EMULATION

SHOW VERSION

 The reading of the "ABORT" label

discards all the parameters read

prior to the "End of

configuration".

 The scanner remains in the last

interface mode when the

scanner is reset.  The label

below should be scanned if the

scanner is configured the first

time.

 The reading of the “ SHOW

VERSION”  label will be show

firmware version.

SCANNING MODE SELECTION(for laser scanner)

For series laser scanners, there are 3 scanning modes to
suit your application requirements.

Trigger Mode

Turbo Trigger Mode

The scanner becomes inactive as
soon as the data is transmitted.  It
must be triggered to become active
again.
The scanner switch is pressed and
double reading for the same bar
code is permitted.  The scanner
will turn off when the trigger switch
is released.

6

Without any scanning, the unit will
enter a standby mode.  To
reactivate the unit, present an
object in front of the IR sensor.
(*Only for Alpha-60 series.)

Object detect Trigger

Note: To avoid hazardous exposure, all laser scanner are 

equipped with an internal cut-off security system 
which will turn off the laser beam after 5 seconds.

SCANNING MODE SELECTION (For Alpha-70
series)

The scanner becomes inactive as
soon as the data is transmitted.  It
must be triggered to become active
again.

In auto scan mode, the scanner is
still active after the data is
transmitted, but the successive
transmission of the same bar code
is not allowed when the trigger
switch is pressed again.

This scanner will light up when
press the scanner trigger switch
once.  And, the scanner will turn
off for next pressing.

For testing the response of the
scanner.

For factory testing use only.

Trigger mode

Auto scan mode

Alternate mode

Repeat mode

Testing mode

DATA REDUNDANT CHECK

The option allow you to set decoder
data redundant check.

Enable

Disable

End of Configuration

7

Summary of Contents for Alpha-50 series































Reviews: