background image

 

 Z-3190BT/Z-3191BT Service Guide  

3 / 11

S

ERVICE  

G

UIDE

Laser Light Viewing

: The scan window is the only aperture through which laser light may be observed from this 

product. A failure of the scanner engine, while the laser diode continues to emit a laser beam, may cause emission 
levels to exceed those for safe operation. The scanner has safeguards to prevent this occurrence. If, however, a 
stationary laser beam is emitted, the failing scanner should be disconnected from its power source immediately. 

 

Adjustments

: Do not attempt any adjustments or alteration of this product. Do not remove the protective housing 

of the scanner. There are no user-serviceable parts inside. 

 

Optical

: The use of optical instruments with this product will increase the eye hazard.  Optical instruments include 

binoculars, magnifying glasses, and microscopes but do not include normal eye glasses worn by the user. 

 

CAUTION

: Use of controls or adjustments or performance of procedures other than those specified herein may 

result in hazardous radiation exposure. 
 
 

For CE-Countries 

 
This scanner is in conformity with CE standards. Please note that an approved, CE-marked power supply unit 
should be used in order to maintain CE conformance. 
 

This manual is in A4 format. Please check your printer setting before printing it out.

 

Power Supply 

 

Use only the type of battery and the charging equipments that came with your scanner. 

 

Using any other type of battery and charging equipment may damage the scanner and invalidate the warranty. 

 

Do not short the battery terminals. The battery could overheat. 

 

Do not attempt to split or peel the outer casing. 

 

Remove the battery if the scanner is not going to be used for a long time. If the battery is left unused for more 

than 3 months, you need to charge the battery before use. 

 

 

WARNING 

 

Improper assembly/disassembly may result in performance degradation to the wireless 
and other functions of the scanner. Use this service guide at your own risk. We do not 
guarantee or warranty the timeliness, completeness, or performance of the information 
provided in this service guide.

Summary of Contents for z3190BT












Reviews: