background image

EN - 8 

 

Do not mount the side of the ComfoAir 
against the wall due to the risk of impact 
sound.

2.6.2  Mounting on the wall 

Mount

 the ComfoAir against a wall with a minimum 

mass of 200 kg/m

2

.

1.  Using a spirit level, fix the mounting bracket ho-

rizontally to the wall. Use M8 anchor bolts. Make 
sure there is enough space under the ComfoAir 
to mount the U bend.

2.  Hang the unit on the mounting bracket.
3.  Mount the condensation drain under the Com-

foAir. The stated dimension of 235 mm is an in-
dication only, and is dependent on the type of 
condensation drain selected.

Make sure to leave a minimum space of 1 metre in 
front of the ComfoAir for carrying out maintenance.
The ComfoAir does not require any space at the si-
des for effective operation.

 

Do not mount the side of the ComfoAir 
against the wall due to the risk of impact 
sound.

2.6.3  Connection of the air ducts

The following aspects must be taken into account, 
while installing the air ducts:

 

Install the air exhaust duct so it drains in the di-
rection of the ComfoAir;

 

Insulate the outside air supply and the air ex-
haust duct between the roof/wall passage to 
render the ComfoAir damp proof. This prevents 
the formation of condensation on the outside of 
the ducts;

  To prevent unnecessary temperature loss in ei-

ther the summer or the winter, we recommend 
fitting thermal and damp-proof insulation to the 
supply ducts from the ComfoAir up to the supply 
valves;

  Install the air ducts with a minimum ø of 125 

mm, as little air resistance as possible and free 
from air leakage;

   Install a silencer of at least 1m straight directly 

onto the supply and return air connections. For 
relevant advice, please contact Zehnder;

  When  using  flexible  channels  only  Zehnder 

channel systems may be used. Any other flexible 
channel will disturb the basic operating principle 
of the balanced ventilation system;

  We recommend that the ventilation system is 

fitted  with  intake  and  exhaust  valves  made  by 
Zehnder.

Supply air

         

Return air

Exhaust air

         

Outside air

ComfoAir 200 - LEFT

Return air

         

Supply air

  

Outside air

         

Exhaust air

 

ComfoAir 200 - RIGHT

Summary of Contents for ComfoAir 200









































Reviews: