background image

The mechanically optical building groups of all Einrichtungenmf AKS become always over a Tubusanpassung (a component of 
all mf-AKS-mechanisms) in the photo exit of the photo tubus (fig. 1/1) and/or installed in the photo exit of the Kontrasttubus (fig. 
5/46).

  

The electronic mf-AKS controller matic.mot is set up stationarily right beside the stand. All remaining electronic building groups can be 
localvariable placed.

  

Fototubus 100/100

  

An adjustable detour element leads the entire light-current alternatively to the visual or to the photo exit. Thus the Tubus is to be 
preferably used for the photography of faint pictures.

  

The Fototubus 100/100 is installed in place of the Fototubus 80/20 100 to the stand:

  

Clamping screw (fig. 2/21) with box spanner loosen, Vergrößerungswechsler off with mounted Fototubus 80/20 100 from the 

stand take.

  

In the Vergrößerungswechsler from downside group of 4 large screws become ago visible, which connect the 

Vergrößerungswechsler with the Fototubus. These screws solve, Fototubus 80/20 100 from the Vergrößerungswechsler tren 
nen and by Fototubus 100/100 replace. Fototubus 100/100 bolt.

  

Complex Vergrößerungswechsler - Fototubus 100/100 on the stand put on, until draw attack forward and indieser situation by 

tightening the clamping screw fix.

  

For the use of the different mf-AKS-mechanisms in en connection with JENAVAL you orient yourselves please in serving guidance to 
micro-photographic putting on camera the system mf-AKS, which is attached to the mechanisms.

  

(18)

 

The secondary observation tube

  

With this mechanism the microscopic picture for two observers sitting next to each other becomes at the same time visibly ge makes. 
Object details can be marked with a shining arrow, which lets itself lead freely across the field.

  

Assembly:

  

Binokulartubus from the stand remove, secondary observation tube in its place set (connecting pieces for light arrow downward 

pointing) and clamp.

  

Binokulartuben set and in comfortable operation position firm wedge.

  

Reducer for eyepieces 30/23.2 into Okularaufnahmedes the Großfeld Binokulartubus use, both Binokulartuben with eyepieces GF-

P 10x (18) equip: The placable eyepiece belongs in the right connecting pieces of the Großfeld Binokulartubus!

 

Cables at the light arrow connecting piece over Trafo to the net on close.

  

Operation:

  

Preparation for observation furnish and after Köhler light up.

  

Light arrow at the Trafo switch on and with handles to the guidance of the light arrow approximately into the center of the field 

bring.

  

Observer at the Großfeld Binokulartubus: Light arrow through out or screwing of the eyepiece of the position of cash eyepiece in 

Summary of Contents for JENAVAL
























Reviews: