Zelmer 28Z015, Instructions For Use Manual

53

Sort out the articles to be ironed according to the type of fabric: wool to 

–

wool, cotton to cotton, etc.

The iron heats faster than cools down, so start ironing from lower tem

-

–

peratures and then increase it.

Test ironing some area on inside of the garment if you are unsure about 

–

the type of fabric. Always start with a low temperature!

Fabrics such as velour or others are best ironed in one direction and 

–

with small pressure to prevent shine marks.

Synthetic fabrics and silk shall be ironed on the inner side of the gar

-

–

ment to avoid shine marks.

INDICATION:

 Ironing without an ironing board. While travelling and when 

no ironing board is available, put a towel on flat surface. Make sure that 

the surface is resistant to warmth and dampness. Do not iron on glass or 

plastic surfaces.

Preparation for operation– first time ironing

Remove  any  protective  films  or  stickers  from  the  sole  plate 

–

(1)

  and 

the cabinet.

Unwind and straighten the power cord.

–

Fill the water tank 

–

(2)

. See “How To Fill Water.”

Connect the iron to a suitable mains supply outlet.

–

Turn the Temperature Dial 

–

(5)

 in clockwise direction to ●●● – position 

–  the  Control  Lamp 

(6)

  glows,  signalling  operation  of  the  immersion 

heater. The  Control  Lamp  goes  off  when  the  required  temperature  is 

reached.

Move the 

–

Steam Control Knob 

(3)

 to 

 position, steam starts coming 

out from the holes in the sole plate.

Begin first time ironing with an old towel.

–

When the water tank is empty and there is no more steam produced, the 

–

preparation work is completed. The iron is now ready for proper use.

After ironing

Move  the Temperature  Dial 

–

(5)

  in  anti-clockwise  direction;  the  iron  is 

switched off.

Disconnect the iron from a mains supply outlet.

–

When the iron gets cool completely, store it vertically in a safe place.

–

The iron set includes a cover which will facilitate storage and protect 

–

the iron during transportation (e.g. against mechanical damage of the 

casing or the soleplate in hand luggage).

Dry ironing

 – Always follow the garment manufacturer’s ironing 

instructions indicated at the garment label.

Connect the iron to a suitable mains supply outlet.

–

Make sure that the Steam Control Knob 

–

(3)

 is set in   position.

Move the Temperature Dial 

–

(5)

 in clockwise direction; set ●, ●● or ●●● 

position.

The  Control  Lamp 

–

(6)

  glows,  signalling  operation  of  the  immersion 

heater and indicating that the iron is on.

The Control Lamp goes off when the required temperature is reached. 

–

The iron is now ready for use.

To switch off the iron, move the Temperature Dial 

–

(5)

 in anti-clockwise 

direction to 

“MIN”

 position.

Disconnect the iron from a mains supply outlet.

–

When the iron gets cool completely, store it vertically in a safe place.

–

Steam ironing

 – Always follow the garment manufacturer’s ironing 

instructions indicated at the garment label.

Fill the water tank 

–

(2)

. See “How To Fill Water.”

Connect the iron to a suitable mains supply outlet. 

–

Move the Temperature Dial 

–

(5)

 in clockwise direction, set ●●● position. 

For optimum steam quality, do not use ● 

or ●● setting for steam ironing. 

The Control Lamp 

–

(6)

 glows, signalling op

-

eration of the immersion heater and indicat

-

ing  that  the  iron  is  on.  The  Control  Lamp 

goes  off  when  the  required  temperature  is 

reached. The iron is now ready for use.