138
QUESTIONS AND ANSWERS CONCERNING THE APPLIANCE
Problem
Cause
Solution
Smoke comes out of the baking
compartment or the vents.
The ingredients stuck to the
baking compartment or to the
outside of the baking tin.
Unplug the appliance and clean the outside of the baking tin or the
baking compartment.
The bread goes down in the
middle and is moist on the
bottom.
The bread was left for too long
in the baking tin after baking
and warming.
Take the bread out off the baking tin before the end of the warming
function.
It is difficult to take the bread
out of the baking tin.
The bottom of the total is stuck
to the kneading peg.
Clean the kneading peg and shaft before the next time you bake
bread. If necessary, fill the container with warm water and leave for
30 minutes. This way the kneading pegs can be easily removed and
cleaned.
The ingredients are not mixed
or the bread is not baked
properly.
Incorrect program setting.
Check the selected menu and other settings.
The START/STOP button was
pressed while the machine was
working.
Do not use the ingredients and start the whole process again.
The lid opened several times
while the machine was working.
The lid can only be opened if the time left on the display is more than
1:30 (this concerns only programs 1,2,3,4)
Make sure the lid was closed properly.
Long blackout while the
machine was working.
Do not use the ingredients and start the whole process again.
The rotation of the kneading
pegs is blocked.
Check if the kneading pegs are not blocked by for example grains, etc.
Pull out the baking tin and check if the drivers turn. If this is not the
case, return the appliance to a service point.
The appliance does not start.
The audible signal goes off. The
display shows the symbol E 01.
The appliance is still hot after
the previous baking process.
Press and hold the START/STOP button until the normal program code
appears on the display. Unplug the appliance. Take out the baking
tin and leave to cool at room temperature. Plug in and restart the
appliance.
The display shows the symbol
“EEE”.
Program or electronic error.
Start the test run. Press and hold the menu button, unplug the
appliance and then plug it in again. Release the button. The appliance
will perform a test run. Unplug the appliance again. The normal
program code should appear on the display. If this is not the case,
return the appliance to a service point.
Summary of Contents for 43Z010
