61
Installing the wall hanger
1. Using a level, draw a vertical line on the wall from the center of the heating plate to the
ceiling. This will ensure a proper and vertical installation of the hanger on the wall.
2. Place the hanger D against the wall with its marked center on the vertical line, the
distance between the holes and the heating plate should be at least 970 mm.
Note: Make sure the hanger D is leveled.
Mark the center of the hanger holes on the wall.
3. Drill the holes marked on the wall using a drill with the diameter of 8mm, fix the hanger
using rawlplugs and screws.
Installing the cooker hood
The cooker hood housing C should be hung on
●
the previously installed hanger D.
Attach the cooker hood to the hanger using a screw
●
(1) – do not tighten the screw until the end.
Level the cooker hood using the screws (2)
●
Tighten the screw (1).
●
The chimney is composed of two u-shaped sec
-
tions with an adjustable height.
In order to fix the upper chimney A to the chim
-
●
ney B (which is permanently fixed to the glass C),
slide both chimneys apart to the desired height.
Screw the upper chimney A tight to the lower
●
chimney B using two screws.
Plug in and operation control
After plugging the appliance in (according to the previously described requirements),
check if the cooker hood lighting works and if its motor operates correctly.
After installing the cooker hood, the socket should be easily accessible in order to unplug
the appliance.
SETTING THE OPERATION MODE
Setting the extraction operation mode
During the extraction mode, air is extracted to the outside with a special duct. Remove
the coal filters with this setting.
The cooker hood is connected to an opening that extracts the air to the outside with a stiff
or flexible duct with the diameter of 150 or 120 mm and appropriate duct clamps which
are to be purchased in installation materials supply stores. The installation should be
performed by a qualified fitter.
Setting the odor absorber operation mode
While using this mode, filtered air comes back to the room through openings on both
sides of the upper chimney. While using this mode, the coal filter should be installed, it is
also recommended to install an air exhaust fin.
The speed of the fan
The lowest and medium speed settings are used in normal conditions and low cooking
fume intensity. The highest speed setting should be used only in case of an intense level
of cooking fumes e.g. during frying or grilling.
Summary of Contents for 524.60
