27
ZCM3821-001_v01
Press the button
4
repeatedly until the required cup symbol for the desired ground coffee
quantity is displayed.
6
5
4
3
2
●
Place an appropriate cup under the coffee delivery spout (e.g. coffee mug).
●
Fill the coffee powder shaft with fresh powdered coffee.
●
Press
(button
6
) and keep it pressed until the desired cup filling amount is
reached.
6
5
4
3
2
●
Release the button. The desired cup filling level is now stored.
Repeat the procedure if you also wish to change the filling level for the
other cup sizes.
All values remain stored even when the coffee machine is switched off.
Should you change your cup size, you can adapt the cup filling level
individually at any time.
The stored cup filling levels for each individual cup symbol only applies in
powder mode.
PREPARING COFFEE SPECIALITIES
The milk system must be connected in order to dispense coffee specialities.More
information can be found in Chapter “CONNECTING THE MILK SYSTEM”.
Do not use soya or rice milk because good frothing results are not possible
with these products.
The milk froth quality is also influenced by the milk type, fat content and
temperature.
You can prepare both “Latte Macchiato” and “Cappuccino” with your appliance. These
differ primarily in the mode of preparation.
When “Latte Macchiato” is prepared, the frothed milk is output first into a tall glass and the
coffee is added subsequently.
The reverse is the case when “Cappuccino” is prepared, first of all the coffee is poured into
the cup, followed by the hot milk froth on top of the coffee.
●
To prepare a “Latte Macchiato”, press button
4
repeatedly until the symbol for the
“Coffee speciality” is selected.
6
5
4
3
2
The appliance heats up to a higher temperature when “Coffee speciality”
is selected. The temperature control lamp flashes during the heating
process.
To prepare Latte Macchiato, first pull the drip tray out of the appliance so
that the taller Latte Macchiato glasses can fit under the coffee outlet.
●
Put one or two glasses under the coffee outlet.
●
In order to reduce heat loss and splashing, adjust the dispensing spout height to suit
your cup/glass size by moving it up or down.
If the height adjuster is difficult to move, clean it. Proceed as described in
section “REMOVING AND CLEANING THE COFFEE DISPENSING UNIT”.
●
Open the rotary switch for milk froth/hot water.
●
Put as much milk froth into the glass as required by taste and preparation mode.
●
You can stop the milk froth output at any time by closing the rotary switch for milk froth/
hot water.
In order to add the required quantity of coffee, select the corresponding cup symbol by
pressing button
4
.
6
5
4
3
2
If “Coffee powder” is selected, only one cup can be used.
The standard filling amounts or the individual filling amounts you set in
Chapter “CHANGING AND SAVING THE CUP FILLING LEVEL IN BEAN
MODE” or “CHANGING AND SAVING THE CUP FILLING LEVEL IN POWDER
MODE” also apply in this mode. If you want to change the cup fill quantity,
you can find the information in the chapters mentioned above.
●
Press
(button
6
) to obtain coffee.
6
5
4
3
2
You can cancel coffee output at any time by pressing
again (button
6
).
Remember that two brewing operations take place in sequence in two cup
mode. Only remove the cups/glasses when both brewing operations are
finished.
A “Cappuccino” is made in the reverse sequence.
You need to use coffee cups, putting the coffee in first and then filling the cups up with
milk froth.
MILK CLEANING SYSTEM AFTER DISPENSING DRINK WITH MILK
After using milk, you should rinse the milk system immediately.
●
Press button
2
repeatedly until the “Milk system cleaning” display is selected.
6
5
4
3
2
●
Press
(button
6
).
6
5
4
3
2
The “Milk system cleaning” symbol and the temperature control lamp flash
while the heating switches on briefly.
After heating is complete, the symbols “Milk system cleaning” and “Milk
froth” flash in the display.
