13
PL
EN
Dry ironing
The steam iron can be used on the dry setting with or without water in the water tank, it is best to avoid
having the water tank full while dry ironing.
Turn the variable steam control to the minimum position.
Select the setting on the temperature control dial best suited for the fabric to be ironed.
CAUTION:
If the steam iron has been used for a long time, it is hot and there is no water. Do not refill it
with water until the steam iron cools down.
Shot of steam
The shot of steam feature provides additional steam for removing stubborn wrinkles.
Set the temperature control to at least the “●●” position.
Press the powerful steam button to release the burst of steam.
NOTE:
To prevent water leakage from the soleplate, do not keep the powerful steam button in
continuously and wait almost 5 seconds between pressures
.
Vertical ironing
Set the temperature control to “max”.
By pressing the shot-steam button at intervals you can also iron vertically (curtains, hung garments, etc.)
NOTE:
To prevent water leakage from the soleplate, do not keep the powerful steam button in
continuously and wait almost 5 seconds between pressures
.
When you finished ironing
Set the temperature dial to the minimum position.
Remove the main plug from the wall socket.
Stand the iron on heel rest.
MANITENANCE AND CLEANING
It is recommended to do the self-cleaning every two weeks if the water in the area is hard or semi-hard if
frequent use of the device is made
Before cleaning the steam iron ensure it is unplugged from the power supply and has completely cooled
down.
Do not use abrasive cleaners.
To clean exterior surfaces, use a damp soft cloth and wipe dry. Do not use any chemical solvents, as
these will damage the surface.
Cleaning the soleplate; Do not use scouring pads or harsh cleaners on the soleplate as these will
damage the surface. To remove burnt residue, iron over a damp cloth while iron is still hot. To clean the
soleplate, simply wipe with soft damp cloth and wipe dry.
Self-cleaning
1. Unplug the iron from the mains socket
2. Set the steam regulator to the
position.
3. Fill the water reservoir.
4. Set the temperature control to its maximum position.
5. Insert the main plug into the wall socket.
6. Allow the iron to heat up until the indicator light turns off.
7. Unplug the steam iron (very important!)
8. Hold the iron over a sink. Press the “clean” button and shake the iron until approximately one third of
the water capacity of the tank is evaporated. Boiling water and steam will be ejected from the holes in
soleplate with impurities washed out
9. Release the “clean” button, and gently shake the iron for some seconds.
Summary of Contents for ZIR3285
