background image

Caring for your ZEN thermostat™

Clean with a damp cloth only. Avoid using chemical cleaning agents.

Rebooting or Resetting to Factory Defaults

If you are experiencing issues, reboot your display by removing and reinserting the batteries. 
This will retain your configuration settings. To restore to factory settings, press the Config button 
on the back of the main display 20 times, the display will beep five times to confirm the reset.

FCC Notice

This device complies with Part 15 of the FCC Rules. Operation is subject to the condition 
that this device does not cause harmful interference. This device complies with Part 15 
of the FCC Rules. Operation is subject to the following two conditions: (1) this device may 
not cause harmful interference, and (2) this device must accept any interference received, 
including interference that may cause undesired operation.

The transmitter must not be co-located or operated in conjunction with any other antenna 
or transmitter.
This equipment complies with the FCC RF radiation exposure limits set forth for an 
uncontrolled environment. This equipment should be installed and operated with a minimum 
distance of 20 cm between the radiator and any part of your body.

NOTE: THE GRANTEE IS NOT RESPONSIBLE FOR ANY CHANGES OR MODIFICATIONS 
NOT EXPRESSLY APPROVED BY THE PARTY RESPONSIBLE FOR COMPLIANCE. SUCH 
MODIFICATIONS COULD VOID THE USER’S AUTHORITY TO OPERATE THE EQUIPMENT.

Industry Canada Notice

This device complies with Industry Canada licence-exempt RSS standard(s). Operation is 
subject to the following two conditions: (1) this device may not cause interference, and (2) 
this device must accept any interference, including interference that may cause undesired 
operation of the device.

Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils 
radio exempts de licence. L'exploitation est autorisée aux deux conditions suivantes : (1) 
l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout 
brouillage radioélectrique subi, même si le brouillage est susceptible d'en compromettre le 
fonctionnement.

Summary of Contents for ZEN-01











Reviews: