background image

Alternatively, installing ZPASS TOUCH system will prevent accidental key 
lockouts. 

3.9   Safety Relock (Rearm—101 A/AS)  

 

(Hold down brake pedal.  Press and release Function Button 4 times and then 
press and release Lock Button) 
 
If the system is in the armed state and the system is disarmed but a door is not 
opened, the system will Safety Rearm automatically within 30 seconds.  
 
Safety relock (rearm) ON 

 

 
Safety relock (rearm) OFF 

 

If safety relock (rearm) occurs, the BLUE LED on the remote control flash once 
and 1 beep will occur.  Paging mode must be ON. 
 
 

3.10   Ignition Lock

   

 

(Hold down brake pedal.  Press and release Function Button 3 times and then 
press and release Remote Start Button) 
 
Ignition Lock will lock the doors if the foot brake is pressed after the key is put into 
key cylinder and turned to the ON position and the engine is running.  The doors 
will relock if a door is opened except for 302S with automatic transmission. 
 
Ignition lock ON

 

 
Ignition lock OFF

 

 
 
 
 
 
 
 

Vehicle 

1 parking light flash & 1 
siren chirp 

Remote 
Control 

1 BLUE LED flash & 1 
beep 

Vehicle 

2 parking light flash & 2 
siren chirps 

Remote Control 

2 BLUE LED flashes & 2 
beeps 

Vehicle 

1 parking light flash & 1 
siren chirp 

Remote Control 

1 BLUE LED flash & 1 
beep 

Vehicle 

2 parking light flash & 2 
siren chirps 

Remote Control 

2 BLUE LED flashes & 2 
beeps 

2.1    Door Lock (Arm—101 A/AS) Press and release 

        

 

 

Depending on installation method, vehicle, and programming of features, these 
indications may or may not occur.  
 
If Zone Bypass has been programmed to be ON, an open door, hood, or trunk will 
be bypassed.   
 
If Zone Bypass has been programmed to be OFF, an open door, hood, or trunk 
will trigger the system.  An open hood or trunk will trigger the system immediately.  
An open door will trigger the system depending upon the Door Trigger Sensing 
programming.  Either a delay of 45 seconds or no delay will occur before an open 
door will trigger the system.   
 
If Zone Bypass has been programmed to No Arm, an open door, hood, or trunk 
will prevent the system from locking the doors and arming the system. 

Successful Door Lock (Arm): 

Vehicle 

1 parking light flash & 1 
siren chirp 

Remote Control 

1 BLUE LED flash & 1 
beep 

Failed due to open door: 

Vehicle 

3 parking light flash & 3 
siren chirp 

Remote Control 

3 RED LED flashes & 3 
beeps 

Failed due to open trunk: 

Vehicle 

4 parking light flashes & 
4 siren chirp 

Remote Control 

4 RED LED flashes & 4 
beeps 

Failed due to open hood: 

Vehicle 

5 parking light flashes & 
5 siren chirp 

Remote Control 

5 RED LED flashes & 5 
beeps 

Failed due to KEY being on ON position: 

Vehicle 

6 parking light flashes & 
6 siren chirp 

Remote Control 

Alternating RED/BLUE 
LED flashes and 6 beeps 

Vehicle 

7 parking light flashes & 
7 siren chirp 

Remote Control 

Alternating RED/BLUE 
LED flashes and 7 beeps 

Failed due to Remote Start already being on: 

Summary of Contents for Z-101 A



















Reviews: